Huawei UPS5000-H-400 kVA Скачать руководство пользователя страница 122

Страница: 122 / 175

7.3 Cold-Starting the UPS Using Batteries

Lead-Acid Battery Cold Start

Step 1 Check that batteries are properly connected. Use a multimeter to measure the

voltage of each battery string. The value should be greater than the specified

value (Voltage of a single battery x Number of batteries in the battery string).

Step 2 Turn off the mains and bypass input switches in the external input PDC, and

switch on the battery circuit breaker. If there are multiple battery strings, switch

on the circuit breaker for each battery string and then the general circuit breaker

between the battery strings and the UPS.

Step 3 Use a multimeter to measure the voltage of each battery string connected to the

UPS. If the voltage is greater than the specified value (Voltage of a single battery

x Number of batteries in the battery string), batteries are connected properly.

Step 4 Press and hold down the BATT START button on the bypass control module for

more than 2 seconds. The system automatically enters the battery cold start state.

The MDU displays the Huawei logo and an initialization progress bar.

Step 5 After the initialization is complete, start the inverter on the LCD.

----End

Lithium Battery Cold Start

Step 1 Check that the cables between the UPS and the lithium battery cabinet are

properly connected.

Step 2 Turn off the mains and bypass input switches in the external input PDC.
Step 3 Power on the lithium battery cabinet by referring to the lithium battery cabinet

manual.

Step 4 Use a multimeter to measure the voltages of the positive and negative battery

strings connected to the UPS battery input terminals. If the measured values are

consistent with the voltages displayed on the System Status screen of the lithium

battery cabinet, the batteries are properly connected.

Step 5 When the green indicator on the battery control unit in the lithium battery cabinet

blinks at 1 Hz or is steady on, press and hold down the BATT START button on

the UPS bypass control module for more than 2 seconds. The system

automatically enters the battery cold start state. The MDU displays the Huawei

logo and an initialization progress bar.

Step 6 After the MDU initialization is complete, start the inverter.

----End

UPS5000-H-(400 kVA-800 kVA)

User Manual (100 kVA Power Module)

7 Single UPS Commissioning

Issue 02 (2021-04-22)

114

Содержание UPS5000-H-400 kVA
















































































































































































Результаты поиска

Содержание UPS5000-H-400 kVA

Отзывы:

Похожие инструкции для UPS5000-H-400 kVA

Бренды по названию

Популярные бренды

Huawei UPS5000-H-400 kVA, Руководство пользователя

Результаты поиска

Содержание UPS5000-H-400 kVA

Отзывы:

Похожие инструкции для UPS5000-H-400 kVA

Бренды по названию

Популярные бренды