Huawei UPS5000-H-400 kVA Скачать руководство пользователя страница 139

Страница: 139 / 175

1. System Settings: On the LCD, choose System Info > Settings > System

Settings. On the WebUI, choose Monitoring > UPS System > Running

Parameter > System Settings.

Table 8-1 System Settings

Item

Setting

Description

Single/Parallel

Set it to

Parallel.

Parallel ID

Number UPSs in

sequence

(example: 1, 2,

3, 4).

Requisite UPSs

Sets it based on

the actual

number of UPSs.

– In a parallel system, the two

parameters must be set to the

same values for all UPSs.

– The total number of UPSs in a

parallel system is the sum of

Requisite UPSs and Redundant

UPSs.

Redundant

UPSs

Sets it based on

the actual

number of UPSs.

2. Battery Settings: On the LCD, choose System Info > Settings > Battery

Settings. On the WebUI, choose Monitoring > Battery System > Running

Parameter > Battery Settings.

Table 8-2 Battery Settings

Item

Setting

Description

Battery string

sharing

Set this

parameter as

required.

If the parallel system shares one

battery string, set this parameter to

Enable.
If each UPS uses an independent

battery string, set this parameter to

Disable.

NO TE

The system may generate alarms such as Rack quantity mismatch, Insufficient

redundant racks, and Inter-rack par. cable alarm. The alarms are automatically cleared 1

minute after you connect all parallel cables.

Step 7 Synchronize parallel parameters.

1. If the Inconsistent parallel param. alarm is generated, choose System Info >

Settings on the LCD and tap Parameter Sync to synchronize parameters

between UPSs in the parallel system.

2. Check that no alarm is generated for any UPS and perform subsequent

operations. If an alarm is generated, follow the troubleshooting suggestion to

clear the alarm first.

UPS5000-H-(400 kVA-800 kVA)

User Manual (100 kVA Power Module)

8 Parallel System Commissioning

Issue 02 (2021-04-22)

131

Содержание UPS5000-H-400 kVA
















































































































































































Результаты поиска

Содержание UPS5000-H-400 kVA

Отзывы:

Похожие инструкции для UPS5000-H-400 kVA

Бренды по названию

Популярные бренды

Huawei UPS5000-H-400 kVA, Руководство пользователя

Результаты поиска

Содержание UPS5000-H-400 kVA

Отзывы:

Похожие инструкции для UPS5000-H-400 kVA

Бренды по названию

Популярные бренды