Huawei UPS5000-H-400 kVA Скачать руководство пользователя страница 166

Страница: 166 / 175

Item

400 kVA/500 kVA/600 kVA

800 kVA

Inverter

overload

capability

Inverter overload capability for front-to-back airflow:
● 105% < load ≤ 110%: transfers to bypass mode after 60 min

or longer (ambient temperature ≤ 30°C)

● 100% < load ≤ 110%: transfers to bypass mode after 60 min

or longer (ambient temperature > 30°C)

● 110% < load ≤ 125%: transfers to bypass mode after 10

minutes or longer

● 125% < load ≤ 150%: transfers to bypass mode after 1

minute or longer

● Load > 150%: The inverter can run for 200 ms or longer and

withstand at least 50 shocks.

Inverter

output short-

circuit

capability

If the initial load rate is less than 40%, the inverter output short-

circuit can tolerate twice the rated current for 300 ms.

Bypass

overload

capability

400 kVA: At 40°C, runs 60 min at

110% load, 10 min at 125%

load, 1 min at 150% load, and

100 ms at over 150% load.
600 kVA: At 25°C, runs

continuously at 125% load;

generates only alarms and

depends on overtemperature

protection at 150% load.

At 30°C: runs continuously at

135% load; generates only

alarms and depends on

overtemperature protection

at 135–150% load.
At 40°C: runs continuously at

125% load; generates only

alarms and depends on

overtemperature protection

at 125–150% load.

Remarks:
Except for the 400 kVA UPS, if the load of the bypass single-

phase or three-phase is 150%–200%, the bypass will be shut

down in 5 minutes, and the hardware depends on

overtemperature protection. If the load of the bypass single-

phase or three-phase is greater than 200%, the bypass will be

shut down in 1 minute, and the hardware depends on

overtemperature protection.

Table 11-9 System electrical specifications

Item

Specifications

Parallel system

reliability

Redundant parallel signals

ECO in a parallel

system

Supported

UPS5000-H-(400 kVA-800 kVA)

User Manual (100 kVA Power Module)

11 Technical Specifications

Issue 02 (2021-04-22)

158

Содержание UPS5000-H-400 kVA
















































































































































































Результаты поиска

Содержание UPS5000-H-400 kVA

Отзывы:

Похожие инструкции для UPS5000-H-400 kVA

Бренды по названию

Популярные бренды

Huawei UPS5000-H-400 kVA, Руководство пользователя

Результаты поиска

Содержание UPS5000-H-400 kVA

Отзывы:

Похожие инструкции для UPS5000-H-400 kVA

Бренды по названию

Популярные бренды