HPE 3PAR StoreServ Скачать руководство пользователя

Страница: 116 / 174

Figure 95: FC onboard ports, controller node enclosure rear view

Figure 96: FC onboard ports LEDs, controller node enclosure rear view

Table 26: FC onboard ports LEDs, controller node enclosure rear view

LED function

Status

State

All ports

Off

Wake up failure (dead device) or power not applied

Port speed

Off

Not connected

3 Fast amber flashes

Connected at 8 Gb/s

4 Fast amber flashes

Connected at 16 Gb/s

Link status

Normal/Connected—link up

Green flashing

Link down or not connected

SAS onboard ports LEDs

IMPORTANT:

For the SAS DP2 port without an SAS cable attached, the amber LED is illuminated

and the green LED is off. This behavior is expected for the DP2 port. For the SAS DP-1 port without
an SAS cable attached, both amber and green LEDs are off.

The controller node has two SAS onboard ports (DP-1 and DP-2) and each includes two LEDs.

116

More information

Содержание 3PAR StoreServ















































































































































































Результаты поиска

Содержание 3PAR StoreServ

Отзывы:

Похожие инструкции для 3PAR StoreServ

Бренды по названию

Популярные бренды

HPE 3PAR StoreServ, Руководство по обслуживанию и модернизации

Результаты поиска

Содержание 3PAR StoreServ

Отзывы:

Похожие инструкции для 3PAR StoreServ

Бренды по названию

Популярные бренды