HPE 3PAR StoreServ Скачать руководство пользователя

Страница: 114 / 174

Controller node LEDs

This information applies only to the controller nodes for the HPE 3PAR StoreServ 8000 Storage system.

IMPORTANT:

The controller nodes in the controller node enclosure are inverted 180° from each

other, as well as the ports.

Figure 92: Controller node LEDs, controller node enclosure rear view

Table 24: Controller node LEDs, controller node enclosure rear view

LED

Function

Status

State

Status

Green solid

Not a cluster member

Green rapid flashing

• Booting

• Shutdown (halted)

Green slow flashing

Cluster member and flashes slowly in
synchronization with the other controller
nodes in the cluster

UID/Service

Blue solid

Shutdown (halted); not a cluster member;
can be removed

Blue flashing

Locate active;

do not remove component

Off

Locate not active

Fault

Amber solid

Fault

Amber flashing

In the cluster, one of the other controller
nodes is shut down (halted).

Off

No fault

Ethernet onboard ports LEDs, controller node enclosure rear view

The controller node has two Ethernet onboard (built-in) ports:

•

MGMT

—Onboard port for the network connection

•

RC-1

—Onboard port for an HPE 3PAR Remote Copy or HPE 3PAR File Persona connection

114

More information

Содержание 3PAR StoreServ















































































































































































Результаты поиска

Содержание 3PAR StoreServ

Отзывы:

Похожие инструкции для 3PAR StoreServ

Бренды по названию

Популярные бренды

HPE 3PAR StoreServ, Руководство по обслуживанию и модернизации

Результаты поиска

Содержание 3PAR StoreServ

Отзывы:

Похожие инструкции для 3PAR StoreServ

Бренды по названию

Популярные бренды