HPE 3PAR StoreServ Скачать руководство пользователя

Страница: 113 / 174

Table 21: 10 Gb iSCSI port LEDs

Green LED

Amber LED

Port state

Off

No link

Off

Amber solid

Boot failure

Green solid

Amber solid

Link up at 10 Gb/s, without traffic

Green flashing

Amber solid

Link up at 10 Gb/s, with traffic

Table 22: 10 GbE NIC port LEDs

Green LED

Amber LED

Port state

Off

No link

Off

Amber solid

Link at the highest speed, 10 GbE

Green flashing

Amber solid

Link at the highest speed and activity

Green solid

Off

Link at the highest speed, 1 GbE

Green flashing

Off

Link at lowest speed and activity

Two-Port 32 Gb FC HBA LEDs

This information applies only to the HPE 3PAR Two-Port 32Gb FC Host Bus Adapter for the HPE 3PAR
StoreServ 8000 Storage system.

Figure 91: HPE 3PAR Two-Port 32Gb FC Host Bus Adapter ports

Table 23: HPE 3PAR Two-Port 32Gb FC Host Bus Adapter LEDs

LED

Function

Status

Port state

Link/Status

Green solid

Normal/connected; link up

Green flashing

Link down or not connected

Port/Speed

Amber flashing

Connected at high speed

Off

Not connected - port failed or power not applied

More information

113

Содержание 3PAR StoreServ















































































































































































Результаты поиска

Содержание 3PAR StoreServ

Отзывы:

Похожие инструкции для 3PAR StoreServ

Бренды по названию

Популярные бренды

HPE 3PAR StoreServ, Руководство по обслуживанию и модернизации

Результаты поиска

Содержание 3PAR StoreServ

Отзывы:

Похожие инструкции для 3PAR StoreServ

Бренды по названию

Популярные бренды