background image

Component ------Summary Description------ Qty

Port      Degraded or failed SFPs           1

Component -Identifier- --Detailed Description--

Port      port:0:1:1   SFP is Degraded

                

port

 suggested action 1

An SFP in a Node-Port is reporting a degraded condition. This is most often caused by the SFP receiver
circuit detecting a low signal level (RX Power Low), and that is usually caused by a poor or contaminated
FC connection, such as a cable. An alert must identify the condition, such as the following:

Port 0:1:1, SFP Degraded (Receiver Power Low: Check FC Cable)

                

Check SFP statistics using CLI commands, such as 

showport -sfp

showport -sfp -ddm

.

cli% 

showport -sfp 0:1:1

N:S:P -State-- -Manufacturer- MaxSpeed(Gbps) TXDisable TXFault RXLoss DDM

0:1:1 OK       HP-F                      8.5 No        No      No     Yes

--------------------------------------------------------------------------

  1

                

In the following example, an RX power level of 522 microwatts (uW) for Port 0:1:1 DDM is a good reading;
and 12 uW for Port 1:1:1 is a weak reading ( < 15 uW). Normal RX power level readings are 300-700 uW.

cli% 

showport -sfp -ddm 0:1:1 1:1:1

--------------Port 0:1:1 DDM--------------

                       -Warning- --Alarm--

--Type-- Units Reading Low  High Low  High

Temp     C     29      -5   85   -10  90  

Voltage  mV    3339    3000 3600 2900 3700

TX Bias  mA    8       2    14   1    17  

TX Power uW    478     158  562  125  631 

RX Power uW    522     15   1000 10   1258 

--------------Port 1:1:1 DDM--------------

                       -Warning- --Alarm--

--Type-- Units Reading Low  High Low  High

Temp     C     33      -5   85   -10  90  

Voltage  mV    3332    3000 3600 2900 3700

TX Bias  mA    7       2    14   1    17  

TX Power uW    476     158  562  125  631 

RX Power uW    98      15   1000 10   1258 

                

port

 example 2

Component -Summary Description- Qty

Port      Missing SFPs            1

Component -Identifier- -Detailed Description--

Port      port:0:3:1   SFP is missing

                

port

 suggested action 2

FC node-ports that normally contain SFPs will report an error if the SFP has been removed. The condition
can be checked using the 

showport -sfp

 command. In this example, the SFP in 1:1:1 has been

removed from the Adapter:

Troubleshooting

159

Содержание 3PAR StoreServ















































































































































































Отзывы: