HP Z400 - Workstation Скачать руководство пользователя

Страница: 218 / 254

Table 6-10

POST error messages (continued)

Screen message

Probable cause

Recommended action

1720—SMART Hard Drive
Detects Imminent Failure

Hard drive is about to fail. (Some hard
disk drives have a firmware patch that
fixes erroneous error messages.)

Determine if the hard disk drive is giving a correct
error message.

Run the Drive Protection System test (if
applicable).

Apply firmware patch (if applicable). See

http://www.hp.com/support

Back up contents and replace the hard disk drive.

1783—Fixed Disk 0/1 locked Hard disk drive failure.

Diagnose the hard disk drive, and replace it if
necessary.

1796—SATA Cabling Error

Missing or improperly attached cable.

Verify that a cable is attached. Reattach the cable.

1797—SATA Drivelock is not
supported in RAID mode

SATA Drivelock is not supported in
RAID mode.

Disable RAID mode, or disable SATA drivelock..

1801—Microcode Update
Error

Unknown or unsupported processor
stepping.

The microcode update failed. Check the processor
stepping to ensure it is a supported stepping. If it is
contact, HP Support.

1802—Processor Not
Supported

The system board does not support the
processor.

Replace the processor with a compatible one.

1803—Processor feature set is
insufficient for current system
settings

Processor feature set is insufficient for
current system settings. The BIOS
settings do not match the support
provided by the processor

Change the BIOS settings or upgrade the processors.

1804—A processor feature
and the memory configuration
are incompatible

A processor feature is incompatible
with the memory configuration.

Restore the previous memory configuration.

ERROR: Invalid 1394 GUID
(Invalid electronic serial
number)

No electronic serial number is stored
with the system.

To assign a serial number , select

Security>System

IDs

in the Computer Setup (F10) Utility.

ERROR: Invalid electronic
serial number (no number)

No electronic serial number is stored
with the system

To assign a serial number , select

Security>System

IDs

in the Computer Setup (F10) Utility.

ERROR: An unsupported
processor is installed. System
halted

Unsupported processor detected.

Replace the processor.

ERROR: A processor requiring
too much power is installed.
System halted

Unsupported processor detected.

Replace the processor.

Invalid electronic serial
number

Incorrect serial number registered in
the system.

Use the Computer Setup (F10) Utility to reset the serial
number.

Network Server Mode Active
and No Keyboard Attached

Keyboard not detected.

Verify that a functioning keyboard is attached to the
workstation.

Processor initialization fails!!!

Processor defective.

Replace the processor.

206

Chapter 6 Diagnostics and troubleshooting

ENWW

Содержание Z400 - Workstation































































































































































































































































Результаты поиска

Содержание Z400 - Workstation

Отзывы:

Похожие инструкции для Z400 - Workstation

Бренды по названию

Популярные бренды

HP Z400 - Workstation, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание Z400 - Workstation

Отзывы:

Похожие инструкции для Z400 - Workstation

Бренды по названию

Популярные бренды