HP Z400 - Workstation страница 188 Скачать руководство пользователя

Страница: 188 / 254

Testing power supply

Before replacing the power supply, use the Built-In Self-Test (BIST) feature to learn if the power supply

still works.

To test the power supply:

Disconnect the AC power.

Remove the internal power supply cables from the system board. (You do not need to remove the

power supply from the chassis.)

If necessary, disconnect the PCIe power cable from the graphics card.

Plug in AC power and verify the following:

●

If the green BIST LED on the rear of the workstation is illuminated

and

the fan is spinning, the

power supply is functional.

●

If the green BIST LED is not illuminated

the fan is not spinning, replace the power supply.

See the

Rear panel components

section of this service guide to locate the BIST LED on this workstation.

Table 6-2

Power supply problems

Problem

Cause

Solution

Power supply shuts down
intermittently.

Power supply fault.

Replace the power supply.

Workstation powers off and the
Power LED flashes red 2 times
(once every second), followed by a
2-second pause.

Processor thermal protection is
activated.

A fan might be blocked or not
turning.

The processor heatsink fan
assembly is not properly
attached to the processor.

Ensure that the workstation air vents are not blocked.

Open the access panel and press the workstation
power button.

Verify that the system fan is running.

Verify that the processor heatsink fan spins.

If the heatsink fan is not spinning, verify that the fan
cable is plugged into the system board connector.
Verify that the fan is properly seated.

Replace the processor heatsink.

Power LED flashes red (once every
2 seconds).

Power failure (power supply is
overloaded).

Determine whether a device is causing the problem
by performing the following:

Disconnect AC power.

Remove all attached devices.

If necessary, disconnect the PCIe power cable
from the graphics card.

Power on the workstation.

If the system enters the POST, perform the following:

Power off the workstation.

Replace one device at a time and repeat this
procedure until a failure occurs.

176

Chapter 6 Diagnostics and troubleshooting

ENWW

Содержание Z400 - Workstation































































































































































































































































Результаты поиска

Содержание Z400 - Workstation

Отзывы:

Похожие инструкции для Z400 - Workstation

Бренды по названию

Популярные бренды

HP Z400 - Workstation, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание Z400 - Workstation

Отзывы:

Похожие инструкции для Z400 - Workstation

Бренды по названию

Популярные бренды