HP Z400 - Workstation Скачать руководство пользователя

Страница: 43 / 254

BIOS ROM

The BIOS ROM is a collection of machine language applications stored as firmware in ROM. It includes

functions such as POST, PCI device initialization, Plug and Play support, power management, and the

Computer Setup (F10) Utility. The BIOS ROM is a 1-MB Serial Peripheral Interface (SPI) port.

See

http://www.hp.com/go/quickspecs

to review the latest BIOS ROM specifications.

The Computer Setup (F10) Utility

This section contains these topics:

Topics

Computer Setup (F10) functionality on page 31

Accessing the Computer Setup (F10) Utility on page 33

The Computer Setup (F10) Utility menu on page 34

Computer Setup (F10) functionality

The Computer Setup (F10) Utility lets you:

●

Change factory default settings and set or change the workstation configuration, which might be

necessary when you add or remove hardware.

●

Determine if all devices installed on the workstation are recognized by the system and functioning.

●

Determine information about the operating environment of the workstation.

●

Solve system configuration errors that are detected but not fixed during the Power-On Self-Test

(POST).

●

Establish and manage passwords and other security features.

●

Establish and manage energy-saving time-outs (not supported on Linux platforms).

●

Modify or restore factory default settings.

●

Set the workstation date and time.

●

Set, view, change, or verify the workstation configuration, including settings for CPU, graphics,

memory, audio, storage, communications, and input devices.

●

Modify the boot order of installed mass storage devices such as SATA, SAS, diskette drives,

optical disk drives, network drives, LS-120 drives and USB boot devices.

●

Configure the boot priority of SATA and SAS hard-drive controllers.

●

Enable or disable Network Server Mode, which lets the workstation start the operating system

when the power-on password is enabled with or without a keyboard or mouse attached. When

attached to the workstation, the keyboard and mouse remain locked until the power-on password

is entered.

●

Enable or disable POST Messages to change the display status of POST messages. POST

Messages disabled suppresses most POST messages, such as memory count, product name, and

ENWW

BIOS ROM

Содержание Z400 - Workstation































































































































































































































































Результаты поиска

Содержание Z400 - Workstation

Отзывы:

Похожие инструкции для Z400 - Workstation

Бренды по названию

Популярные бренды

HP Z400 - Workstation, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание Z400 - Workstation

Отзывы:

Похожие инструкции для Z400 - Workstation

Бренды по названию

Популярные бренды