manualshive.com logo in svg

HP Z400 - Workstation, Руководство по техническому обслуживанию и ремонту

HP Z400 - рабочая станция. Установочное руководство и другие руководства для этого продукта доступны для бесплатного скачивания на {вебсайте}. Получите всю необходимую информацию для установки и использования вашей рабочей станции HP Z400.

Поделиться
Скачать
background image

Diagnostic codes and errors .................................................................................................. 195

Diagnostic LED and audible (beep) codes ................................................................ 195
LED color definitions .............................................................................................. 199
POST error messages ............................................................................................ 201

7  Configuring RAID devices .............................................................................................. 207

Maximum hard drive configurations ....................................................................................... 207
Configuring SATA RAID devices ............................................................................................ 208

Attaching SATA HDDs ........................................................................................... 208
Configuring system BIOS ....................................................................................... 209
Creating RAID volumes .......................................................................................... 210

Configuring SAS RAID devices .............................................................................................. 211

Supported configurations ....................................................................................... 211
SAS RAID 0 configuration ...................................................................................... 212
SAS RAID 1 configuration ...................................................................................... 213
SAS RAID 1E configuration .................................................................................... 214
Deleting RAID volumes ........................................................................................... 215

8  Configuring password security and resetting CMOS ...................................................... 216

Preparing to configure passwords .......................................................................................... 217
Resetting the password jumper ............................................................................................... 218
Clearing and Resetting the CMOS ......................................................................................... 219

Using the CMOS Button ......................................................................................... 219
Using the Computer Setup (F10) Utility to Reset CMOS .............................................. 220

Appendix A  Connector pins ............................................................................................. 221

Appendix B  System board designators ............................................................................ 231

Appendix C  Routine Care ................................................................................................. 233

General cleaning safety precautions ....................................................................................... 233
Cleaning the workstation case ............................................................................................... 233
Cleaning the keyboard ......................................................................................................... 233
Cleaning the monitor ............................................................................................................ 234
Cleaning the mouse .............................................................................................................. 234

Appendix D  Locating HP resources ................................................................................... 235

Product information .............................................................................................................. 236
Product support .................................................................................................................... 237
Product documentation ......................................................................................................... 238
Product diagnostics .............................................................................................................. 239
Product updates ................................................................................................................... 240

ENWW

xi

Содержание Z400 - Workstation































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Z400 - Workstation

Hand Held Products 4800p Quick Start Manual preview
4800p
Бренд: Hand Held Products Страницы: 20
Harbor Freight Tools ZURICH OBD2 Owner'S Manual preview
ZURICH OBD2
Бренд: Harbor Freight Tools Страницы: 36
Magtek MT-215232 Technical Reference Manual preview
MT-215232
Бренд: Magtek Страницы: 28
Advantech PCM-3641I Startup Manual preview
PCM-3641I
Бренд: Advantech Страницы: 2
Eonon G2225 Instruction Manual preview
G2225
Бренд: Eonon Страницы: 16
Blaupunkt New Jersey MP68 Operating And Installation Manual preview
New Jersey MP68
Бренд: Blaupunkt Страницы: 74
Jula 709-115 Operating Instructions Manual preview
709-115
Бренд: Jula Страницы: 19
Daewoo AGC-4208 Series Service Manual preview
AGC-4208 Series
Бренд: Daewoo Страницы: 52
Datalogic QuickScan I QM21X1 Quick Reference Manual preview
QuickScan I QM21X1
Бренд: Datalogic Страницы: 48
Datalogic Magellan 83 Quick Reference Sheet preview
Magellan 83
Бренд: Datalogic Страницы: 2
ACS ACR30S Driver Installation Manual preview
ACR30S
Бренд: ACS Страницы: 22
Blackberry PRD-09695-004 - SMART Card Reader Manual preview
PRD-09695-004 - SMART Card Reader
Бренд: Blackberry Страницы: 28
Rosewill RCR-IC001 User Manual preview
RCR-IC001
Бренд: Rosewill Страницы: 1
SIB RF005 Manual preview
RF005
Бренд: SIB Страницы: 4
Ingenico Moby/8500 User Manual preview
Moby/8500
Бренд: Ingenico Страницы: 10
SoundMax SM-CCR3049F Instruction Manual preview
SM-CCR3049F
Бренд: SoundMax Страницы: 32
StarTech.com PEX2EC35 User Manual preview
PEX2EC35
Бренд: StarTech.com Страницы: 11
Mindeo CS2290 Quick Manual preview
CS2290
Бренд: Mindeo Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды