manualshive.com logo in svg

HP Z400 - Workstation, Руководство по техническому обслуживанию и ремонту

HP Z400 - рабочая станция. Установочное руководство и другие руководства для этого продукта доступны для бесплатного скачивания на {вебсайте}. Получите всю необходимую информацию для установки и использования вашей рабочей станции HP Z400.

Поделиться
Скачать
background image

Table 6-8

  Diagnostic lights and audible codes (continued)

Activity

Possible cause

Recommended action

Red Power LED blinks four
times, once every second,
followed by a two-second
pause. Four beeps.

Power failure (power supply
is overloaded)

CAUTION:

Internal components might be powered even when the

workstation is off. To prevent damage, disconnect the workstation power
cord before you remove a component.

1.

Open the access panel and ensure that all power connections (24-
pin Main, 4-pin CPU) are secure on the system board.

2.

Check if a device is causing the problem by removing 

all

 attached

devices (such as hard, diskette, or optical disk drives, and
expansion cards.) Power on the computer. If the system enters the
POST, power off and replace one device at a time; repeat this
procedure until failure occurs. Replace the device that is causing the
failure. Continue adding devices one at a time to ensure all devices
are functioning properly.

3.

(For computers with a BIST LED on the rear panel) Check the power
supply functionality:

a.

Disconnect the AC power.

b.

Disconnect ALL internal power supply cables.

c.

Plug in the AC power.

d.

Power on the computer.

●

If the power supply fan spins and the BIST LED lights, the
power supply is functional. The problem might be on the
system board. Contact HP for assistance.

●

If the power supply fan does not spin or the BIST LED
does not light, the problem might be in the power supply.
Contact HP for assistance.

Red Power LED blinks five
times, once every second,
followed by a two-second
pause. Five beeps.

Pre-video memory error

CAUTION:

Internal components might be powered even when the

workstation is off. To prevent damage, disconnect the workstation power
cord before you remove a component.

1.

Reseat DIMMs.

2.

Replace DIMMs one at a time to isolate faulty module.

3.

Replace third-party memory with HP memory.

4.

The problem might be on the system board. Contact HP for
assistance.

Red Power LED blinks six
times, once every second,
followed by a two-second
pause. Six beeps.

Pre-video graphics error.

CAUTION:

Internal components might be powered even when the

workstation is off. To prevent damage, disconnect the workstation power
cord before you remove a component.

1.

Reseat the graphics card.

2.

Verify the graphics auxiliary power cable is connected (if
applicable).

3.

The problem might be on the graphics card. Contact HP for
assistance.

ENWW

Diagnostic codes and errors

197

Содержание Z400 - Workstation































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Z400 - Workstation

IBM 5710 Installation And Using Manual preview
5710
Бренд: IBM Страницы: 52
StarTech.com 35FCREADBK2 Installation Manual preview
35FCREADBK2
Бренд: StarTech.com Страницы: 2
Icarus Illumina User Manual preview
Illumina
Бренд: Icarus Страницы: 59
EarthWay Ev-N-Spred 2050 Assembly And Operating Instructions preview
Ev-N-Spred 2050
Бренд: EarthWay Страницы: 2
Konica Minolta KIP 2100 User Manual preview
KIP 2100
Бренд: Konica Minolta Страницы: 153
Hauppauge Colossus 2 Quick Installation Manual preview
Colossus 2
Бренд: Hauppauge Страницы: 2
Jensen JWM30 Installation And Owner'S Manual preview
JWM30
Бренд: Jensen Страницы: 16
DAQ system PCIe-DIO6400 User Manual preview
PCIe-DIO6400
Бренд: DAQ system Страницы: 21
Ozito Powe X Change PXCUSS-018 Instruction Manual preview
Powe X Change PXCUSS-018
Бренд: Ozito Страницы: 6
Boss Audio Systems BV7464B User Manual preview
BV7464B
Бренд: Boss Audio Systems Страницы: 35
Jamex 9550 MP3000 User Manual preview
9550 MP3000
Бренд: Jamex Страницы: 15
ACS CryptoMate EVO User Manual preview
CryptoMate EVO
Бренд: ACS Страницы: 45
ACS PocketMate II ACR39U-N1 User Manual preview
PocketMate II ACR39U-N1
Бренд: ACS Страницы: 44
TGM PSION WORKABOUT PRO Instruction Manual preview
PSION WORKABOUT PRO
Бренд: TGM Страницы: 40
Boss Audio Systems DVD-5000B User Manual preview
DVD-5000B
Бренд: Boss Audio Systems Страницы: 16
Boss Audio Systems CD-4500R User Manual preview
CD-4500R
Бренд: Boss Audio Systems Страницы: 18
WilTec 50141 Operation Manual preview
50141
Бренд: WilTec Страницы: 4
Lindy 20789 Manual preview
20789
Бренд: Lindy Страницы: 60

Бренды по названию

Популярные бренды

Загрузить еще бренды