HP Z400 - Workstation Скачать руководство пользователя

Страница: 54 / 254

Table 4-1

Computer Setup (F10) Utility menu descriptions (continued)

Heading

Option

Description

Chipset/ Memory Enable/disable these options:

●

PCI SERR# Generation (Enable or Disable)—Controls PCI SERR#
generation for ill-behaved PCI add-in cards (that can generate SERR#
spuriously).

●

PCI VGA Palette Snooping (Enable or Disable)—Controls PCI VGA Palette
Snooping for compatibility purposes.

●

Memory Mode Interleave—Sets interleave mode for dual socket
workstations.

Device Options

Lets you set the following device options:

●

Num Lock State at Power-On (On or Off)

●

S5 Wake-on-LAN (Enable or Disable)

●

Multiprocessor (Activates a single core.)

●

Unique Sleep State Blink Rates (Enable or Disable)

●

Internal speaker

●

Monitor Tracking (Enable or Disable)

●

NIC PXE Option ROM

Download (Enable or Disable)

●

SAS Option ROM

Download (Enable or Disable) (Not available on some

workstations.)

●

SATA RAID Option ROM

Download (Enable or Disable)

Available on selected models

These options should be used by advanced users only

Chapter 4 System management

ENWW

Содержание Z400 - Workstation































































































































































































































































Результаты поиска

Содержание Z400 - Workstation

Отзывы:

Похожие инструкции для Z400 - Workstation

Бренды по названию

Популярные бренды

HP Z400 - Workstation, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание Z400 - Workstation

Отзывы:

Похожие инструкции для Z400 - Workstation

Бренды по названию

Популярные бренды