manualshive.com logo in svg

HP Z400 - Workstation, Руководство по техническому обслуживанию и ремонту

HP Z400 - рабочая станция. Установочное руководство и другие руководства для этого продукта доступны для бесплатного скачивания на {вебсайте}. Получите всю необходимую информацию для установки и использования вашей рабочей станции HP Z400.

Поделиться
Скачать
background image

Slots one and three use open-ended PCIe connectors, so a PCIe x16 card can be inserted. Graphics

cards greater than 75 watts require the use of an auxiliary power cable adapter.

Card configuration restrictions for power supplies

CAUTION:

To prevent damage, the overall power consumption of the workstation (including I/O

cards, CPU, and memory) must not exceed the maximum rating of the workstation power supply. For

power supply information, see 

Power supply specifications on page 10

.

The maximum graphics configurations are:

●

475W power supply

◦

A graphics card up to 150W in the primary graphics slot

◦

A second graphics card in the second PCIe2 x16 slot (slot 4), provided the combined power

consumption of both cards does not exceed 150W

●

600W power supply

◦

A graphics card up to 250W in the primary graphics slot

◦

A second graphics card in the second PCIe2 x16 slot (slot 4), provided the combined power

consumption of both cards does not exceed 250W

If you use a graphics card with greater than 75 watts of power, leave the adjacent slot empty. The

maximum graphics power depends on CPU and memory selections. Follow any additional workstation

configuration restrictions.

122

Chapter 5   Replacing components

ENWW

Содержание Z400 - Workstation































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Z400 - Workstation

AccessPRO SF101 Installation Manual preview
SF101
Бренд: AccessPRO Страницы: 8
M-Audio Lagoon Manual preview
Lagoon
Бренд: M-Audio Страницы: 28
Raymer 852 Installation And Operation Instructions preview
852
Бренд: Raymer Страницы: 3
MAC Audio StarX 2.16 Owner'S Manual/Warranty Document preview
StarX 2.16
Бренд: MAC Audio Страницы: 20
Aiwa YKZA3RDF Service Manual preview
YKZA3RDF
Бренд: Aiwa Страницы: 22
Franklin IC-119 User Manual preview
IC-119
Бренд: Franklin Страницы: 42
TBS technologies TBS6304 User Manual preview
TBS6304
Бренд: TBS technologies Страницы: 22
RTscan RT214 Integration Manual preview
RT214
Бренд: RTscan Страницы: 28
Alpine CDE-111R Owner'S Manual preview
CDE-111R
Бренд: Alpine Страницы: 37
Exar Stretch VRC7000 Series Installer'S Manual preview
Stretch VRC7000 Series
Бренд: Exar Страницы: 8
Symbol DS3578 Quick Start Manual preview
DS3578
Бренд: Symbol Страницы: 2
DAT S3Q-PCIe22 User Manual preview
S3Q-PCIe22
Бренд: DAT Страницы: 3
Lexar MULTI-CARD 25-IN-1 Quick Start Manual preview
MULTI-CARD 25-IN-1
Бренд: Lexar Страницы: 10
ICP DAS USA PCI-P8R8 User Manual preview
PCI-P8R8
Бренд: ICP DAS USA Страницы: 40
Kobo N647B User Manual preview
N647B
Бренд: Kobo Страницы: 37
Soundstream VIR-7200 Operating Instructions Manual preview
VIR-7200
Бренд: Soundstream Страницы: 31
Denver CAD-495 Instruction Manual preview
CAD-495
Бренд: Denver Страницы: 8
Domain DM-DV703USB Instruction Manual preview
DM-DV703USB
Бренд: Domain Страницы: 14

Бренды по названию

Популярные бренды

Загрузить еще бренды