HP Z400 - Workstation Скачать руководство пользователя страница 189

Страница: 189 / 254

Table 6-2

Power supply problems (continued)

Problem

Cause

Solution

Replace the device causing the failure

Continue adding devices one at a time to verify
that all devices are functioning.

Verify power supply functionality.

Disconnect AC power.

Remove the internal power supply cables from
the system board. (You do not need to remove
the power supply from the chassis.)

If necessary, disconnect the PCIe power cable
from the graphics card.

Plug in AC power.

●

If the power supply fan spins and the LED
illuminates, the power supply is good.
Replace the system board.

●

If the power supply fan does not spin or
the LED does not illuminate, replace the
power supply.

Solving diskette problems

Table 6-3

Diskette problems

Problem

Cause

Solution

Diskette drive light stays on.

Diskette is damaged.

Right-click

Start

, select

Explore

, and then select a

drive.

Select

File>Properties>Tools

Under Error-checking, select

Check Now.

Diskette is incorrectly inserted.

Remove and reinsert diskette.

Files on the diskette are
damaged.

Verify the program diskettes.

Drive cable is not properly
connected.

Reconnect the power cable and verify that all four pins
are connected.

Drive not found.

Cable is loose.

Reseat the diskette drive data and power cables.

Removable drive is not seated
properly.

Reseat the drive.

ENWW

Troubleshooting scenarios and solutions

177

Содержание Z400 - Workstation































































































































































































































































Результаты поиска

Содержание Z400 - Workstation

Отзывы:

HP Z400 - Workstation, Руководство по техническому обслуживанию и ремонту, Страница: 189 / 254

Результаты поиска

Содержание Z400 - Workstation

Отзывы: