HP Z400 - Workstation страница 192 Скачать руководство пользователя

Страница: 192 / 254

Table 6-4

Hard drive problems (continued)

Problem

Cause

Solution

Nonsystem disk or NTLDR missing
message.

System is trying to start from a
nonbootable diskette.

Remove the diskette from the drive.

System is trying to start from a
damaged hard drive.

Insert a bootable diskette into the drive and restart
the workstation.

If the hard drive is still inaccessible and MBR Security
is enabled, try restoring the previously saved
MBR image by entering Setup and selecting

Security>Restore Master Boot Record

System files missing or not
properly installed.

Insert a bootable system diskette and restart.

Verify that the hard drive is partitioned and
formatted.

Install the system files for the appropriate operating
system, if necessary.

Hard drive boot disabled in
Computer Setup.

Run the Computer Setup (F10) Utility and enable the hard
drive entry in the Storage>Boot Order list.

Workstation will not start.

Hard drive is damaged.

Replace the hard drive.

180

Chapter 6 Diagnostics and troubleshooting

ENWW

Содержание Z400 - Workstation































































































































































































































































Результаты поиска

Содержание Z400 - Workstation

Отзывы:

Похожие инструкции для Z400 - Workstation

Бренды по названию

Популярные бренды

HP Z400 - Workstation, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание Z400 - Workstation

Отзывы:

Похожие инструкции для Z400 - Workstation

Бренды по названию

Популярные бренды