HP Z400 - Workstation страница 216 Скачать руководство пользователя

Страница: 216 / 254

Table 6-10

POST error messages (continued)

Screen message

Probable cause

Recommended action

513—Front Chassis fan not
detected

Front fan missing, disconnected, or
defective.

Reseat the fan cable.

Reseat the fan.

Replace the fan.

514—Memory fan not
detected

Memory fan missing, disconnected, or
defective.

Reseat the fan cable.

Reseat the fan.

Replace the fan.

515—CPU Overtemp
occurred

Insufficient processor cooling or
processor defect.

If necessary, add a heatsink to the processor and
ensure proper operation.

Replace the processor.

516—Chipset fan not detected Chipset fan missing, disconnected, or

defective.

Ensure that the fan is installed and connected
properly.

Replace the fan.

517—Low power CPU
heatsink(s) detected for high
power CPUs

Inadequate heatsink is installed.

Replace the low power heatsink with a high power
heatsink.

518—Power supply wattage
insufficient for hardware
configuration

Workstation configuration requires
more power than the power supply
can provide.

Reduce the workstation power consumption.

Replace the power supply with a high output
power supply.

601—Diskette Controller Error Diskette controller circuitry or diskette

drive circuitry incorrect.

Run the Computer Setup (F10) utility.

Verify cabling and replace defective cables if
necessary.

Clear CMOS.

Replace the diskette drive.

Replace the system board.

605—Diskette Drive Type
Error

Mismatch in drive type.

Run the Computer Setup (F10) Utility.

Disconnect any other diskette controller devices
(tape drives).

Clear the CMOS.

610—External Storage Device
Failure

External storage device is not
detected, is improperly connected, or
is defective.

Verify that the external device is present and
connected properly.

Replace the external device.

611—Primary Floppy Port
Address Assignment Conflict

The flexible disk drive is configured at
a previously assigned address.

Select a new address for the flexible disk drive.

912—Computer Cover Has
Been Removed Since Last
System Start Up

N/A

No action required.

204

Chapter 6 Diagnostics and troubleshooting

ENWW

Содержание Z400 - Workstation































































































































































































































































Результаты поиска

Содержание Z400 - Workstation

Отзывы:

Похожие инструкции для Z400 - Workstation

Бренды по названию

Популярные бренды

HP Z400 - Workstation, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание Z400 - Workstation

Отзывы:

Похожие инструкции для Z400 - Workstation

Бренды по названию

Популярные бренды