HP Z400 - Workstation страница 62 Скачать руководство пользователя

Страница: 62 / 254

ROM Flash

HP workstations include a programmable flash ROM. By establishing a setup password in the

Computer Setup (F10) Utility, you can protect the ROM from being inadvertently updated or

overwritten. This function is important to ensure the operating integrity of the workstation.

To upgrade the ROM, download the latest SoftPaq images from

http://www.hp.com/support/

workstation_swdrivers

For maximum ROM protection, establish a setup password. The setup password prevents unauthorized

ROM upgrades. SSM lets you create the setup password on several workstations simultaneously.

Remote ROM Flash

Remote ROM Flash lets system administrators safely upgrade the ROM on remote HP workstations from

a centralized network management console. This permits consistent deployment and greater control of

HP PC ROM images over the network.

To use Remote ROM Flash, the workstation must be powered on, or turned on using Remote Wakeup.

For more information about Remote ROM Flash and HPQFlash, see the HP Client Manager Software or

System Software Manager sections at

http://www.hp.com/go/ssm

HPQFlash

The HPQFlash utility locally updates or restores the system ROM on PCs using a Windows operating

system. For more information about HPQFlash, see

http://www.hp.com/go/ssm

, and enter the name

of the workstation.

Chapter 4 System management

ENWW

Содержание Z400 - Workstation































































































































































































































































Результаты поиска

Содержание Z400 - Workstation

Отзывы:

Похожие инструкции для Z400 - Workstation

Бренды по названию

Популярные бренды

HP Z400 - Workstation, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание Z400 - Workstation

Отзывы:

Похожие инструкции для Z400 - Workstation

Бренды по названию

Популярные бренды