HP Z400 - Workstation Скачать руководство пользователя

Страница: 37 / 254

Ordering backup software

If you cannot create system recovery CDs or DVDs, you can order a recovery disk set from the HP

support center. To obtain the support center telephone number for your region see

http://www.hp.com/support/contactHP

Restoring Windows 7 or Windows Vista

This section describes how to restore Windows 7 or Windows Vista.

Ordering the RestorePlus! media

If you ordered restore media with your workstation, the media is included with your workstation

components.

If you did not order restore media, call HP Support and request a RestorePlus! media kit. For worldwide

technical support phone numbers, see

http://www.hp.com/support

Restoring the operating system

NOTE:

Windows 7 and Windows Vista provide a backup and restore application as well. To learn

more about this application, see the Microsoft Web site.

CAUTION:

Before you restore the operating system, back up your data.

When you run RestorePlus! from media, the process deletes all information on the primary hard drive,

including all partitions.

To restore Windows 7 or Windows Vista:

Boot from the RestorePlus! DVD to start the RestorePlus! process. You must start from the

RestorePlus! DVD to install device drivers and settings.

Follow the prompts to restore your operating system.

Some application software might not be restored using this process. If software is not restored, install it

from the appropriate application DVD.

ENWW

Ordering backup software

Содержание Z400 - Workstation































































































































































































































































Результаты поиска

Содержание Z400 - Workstation

Отзывы:

Похожие инструкции для Z400 - Workstation

Бренды по названию

Популярные бренды

HP Z400 - Workstation, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание Z400 - Workstation

Отзывы:

Похожие инструкции для Z400 - Workstation

Бренды по названию

Популярные бренды