HP Z400 - Workstation Скачать руководство пользователя

Страница: 129 / 254

Figure 5-44

6–DIMM load order

Supported DIMM configurations

The workstation supports these DIMM arrangements, depending on which Z400 product you order:

●

Up to six DIMM slots

●

Memory range from 1 GB to 16GB for the 4-DIMM product

●

Memory range from 1 GB to 24GB for the 6-DIMM product

●

No support for mirroring

●

No support for DIMM sparing

BIOS errors and warnings

The BIOS generates warnings/errors on invalid memory configurations:

●

If the BIOS can find a valid memory configuration by disabling plugged-in memory, it does so and

reports a warning during POST. the workstation can still be started. The warning will indicate the

location of the failed DIMM on the system board.

●

If there is no way for the BIOS to obtain a valid memory configuration by disabling plugged-in

memory, the BIOS halts with a diagnostics 2006 code for memory error (five beeps and blinks).

ENWW

Removing and installing components

117

Содержание Z400 - Workstation































































































































































































































































Результаты поиска

Содержание Z400 - Workstation

Отзывы:

Похожие инструкции для Z400 - Workstation

Бренды по названию

Популярные бренды

HP Z400 - Workstation, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание Z400 - Workstation

Отзывы:

Похожие инструкции для Z400 - Workstation

Бренды по названию

Популярные бренды