manualshive.com logo in svg

HP Z400 - Workstation, Руководство по техническому обслуживанию и ремонту

HP Z400 - рабочая станция. Установочное руководство и другие руководства для этого продукта доступны для бесплатного скачивания на {вебсайте}. Получите всю необходимую информацию для установки и использования вашей рабочей станции HP Z400.

Поделиться
Скачать
background image

Table 6-8

  Diagnostic lights and audible codes

Activity

Possible cause

Recommended action

Blue Power LED on. No
beeps.

Workstation on.

N/A

Blue Power LED blinks every
two seconds. No beeps.

Workstation in Sleep mode
(S3-Suspend to RAM). Select
models only.

Blue Power LED is off. No
beeps.

Workstation in Hibernate
mode (S4-Suspend to disk)
or off state (S5).

Blue Power LED blinks three
times*, once per second.
No beeps.

Workstation in Sleep mode
(S3-Suspend to RAM). Select
models only.

Blue Power LED blinks four
times*, once per second.
No beeps.

Workstation in Hibernate
mode (S4-Suspend to disk).

* User-selectable. The BIOS option you select controls the
blue LED function during these suspend modes. See 

The

Computer Setup (F10) Utility menu on page 34

 for details.

For the following LED activity and beeps, the beeps are heard through the chassis speaker. Blinks and beeps repeat for 5 cycles, after
which, only the blinks continue to repeat.

Red Power LED blinks two
times, once every second,
followed by a two-second
pause. Two beeps.

CPU thermal protection
activated by either of the
following methods:

●

A fan might be blocked
or not turning.

●

The heatsink and fan
assembly is not
properly attached to
the CPU.

CAUTION:

Internal components might be powered even when the

workstation is off. To prevent damage, disconnect the workstation power
cord before you remove a component.

1.

Ensure that the workstation air vents are not blocked and the
cooling fan is running.

2.

Open the access panel, press power button, and verify that the CPU
fan is spinning. If the CPU fan is not spinning, make sure the fan
cable is plugged into the workstation board header. Ensure the fan
is fully and properly seated or installed.

3.

If fan is plugged in and seated properly, but is not spinning, the
problem might be in the CPU fan. Contact HP for assistance.

4.

Verify that the fan assembly is properly attached. If problems
persist, there might be a problem with the CPU heatsink. Contact
HP for assistance.

Red Power LED blinks three
times, once every second,
followed by a two-second
pause. Three beeps.

CPU not installed (not an
indicator of bad CPU).

1.

Verify that the CPU is present.

2.

Reseat the CPU.

196

Chapter 6   Diagnostics and troubleshooting

ENWW

Содержание Z400 - Workstation































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Z400 - Workstation

Baracoda 2604 User Manual preview
2604
Бренд: Baracoda Страницы: 9
Nakamichi NA85 Instruction Manual preview
NA85
Бренд: Nakamichi Страницы: 12
Nakamichi NA 1550 User Manual preview
NA 1550
Бренд: Nakamichi Страницы: 18
Rauch SA 250 Operator'S Manual preview
SA 250
Бренд: Rauch Страницы: 32
Vais Technology iVIC-6DR Manual preview
iVIC-6DR
Бренд: Vais Technology Страницы: 8
TOP VEHICLE TECH GR3BMW17 Installation Manual preview
GR3BMW17
Бренд: TOP VEHICLE TECH Страницы: 8
Soundstream VR-74H2B Operation Instructions Manual preview
VR-74H2B
Бренд: Soundstream Страницы: 31
Insignia NS-MCR17MUSB Quick Setup Manual preview
NS-MCR17MUSB
Бренд: Insignia Страницы: 2
Q-See QSDT8PCRP User Manual preview
QSDT8PCRP
Бренд: Q-See Страницы: 97
BluStream ADC11AU User Manual preview
ADC11AU
Бренд: BluStream Страницы: 6
Lanzar VBD2400U Instruction Manual preview
VBD2400U
Бренд: Lanzar Страницы: 8
StarTech.com PCI1394MP Instruction Manual preview
PCI1394MP
Бренд: StarTech.com Страницы: 8
Pocketbook InkPad X PB1040 User Manual preview
InkPad X PB1040
Бренд: Pocketbook Страницы: 104
SMC Networks EZ Connect g SMCWPCI-G User Manual preview
EZ Connect g SMCWPCI-G
Бренд: SMC Networks Страницы: 50
Obreey Basi? New 613 User Manual preview
Basi? New 613
Бренд: Obreey Страницы: 54
Denver CAD-495 Instruction Manual preview
CAD-495
Бренд: Denver Страницы: 8
Hilti AI S1/4 User Manual preview
AI S1/4
Бренд: Hilti Страницы: 179
Boss Audio Systems MP3-3O6OR User Manual preview
MP3-3O6OR
Бренд: Boss Audio Systems Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды