HP Z400 - Workstation страница 187 Скачать руководство пользователя

Страница: 187 / 254

Table 6-1

Minor problems (continued)

Problem

Cause

Possible Solution

CAUTION:

Internal components might be powered even when the

workstation is off. To prevent damage, disconnect the workstation
power cord before you remove a component.

Diagnose faulty device

To verify the presence of a faulty device, you must disconnect all
devices one at a time, removing the graphics card last:

Disconnect AC power to the computer.

Disconnect a device (graphics card last).

Reconnect AC power

Power on the computer.

◦

If the computer powers on successfully, follow the procedures
in this guide to replace the device that you most recently
disconnected.

◦

If the computer cannot power on, then repeat this procedure
to remove another device until you identify the faulty device.

◦

If no faulty device is found, replace the system board.

CAUTION:

Internal components might be powered even when the

workstation is off. To prevent damage, disconnect the workstation
power cord before you remove a component.

Diagnose power supply problem

Verify that the workstation is plugged into a working AC outlet.

Verify that the power button harness is connected to the inline front
panel I/O device assembly connector.

Verify power supply functionality:

Disconnect the AC power.

Remove the internal power supply cables from the system
board. (You do not need to remove the power supply from
the chassis.)

Reconnect the AC power.

Turn on the computer.

●

If the power supply fan spins and the BIST LED
illuminates, the power supply is good. Replace the
system board.

●

If the power supply fan does not spin or the LED does
not illuminate, there may be a problem with the power
supply. See

Testing power supply on page 176

for

more information.

Solving power supply problems

This section presents power supply troubleshooting scenarios.

ENWW

Troubleshooting scenarios and solutions

175

Содержание Z400 - Workstation































































































































































































































































Результаты поиска

Содержание Z400 - Workstation

Отзывы:

Похожие инструкции для Z400 - Workstation

Бренды по названию

Популярные бренды

HP Z400 - Workstation, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание Z400 - Workstation

Отзывы:

Похожие инструкции для Z400 - Workstation

Бренды по названию

Популярные бренды