HP Z400 - Workstation страница 81 Скачать руководство пользователя

Страница: 81 / 254

Tools and software requirements

The tools necessary for workstation component removal and installation are:

●

Torx T-15 driver

●

Flat blade and cross-tip screwdrivers

●

Diagnostics software

Special handling of components

The components included in this section require special handling when servicing the workstation.

WARNING!

Do not use the front bezel as a handle or lifting point when lifting or moving the

workstation. Lifting the workstation from the front bezel, or lifting it incorrectly, could cause the

workstation to fall, causing possible injury to you and damage to the workstation. To properly and

safely lift the workstation, lift from the bottom of the workstation.

Cables and connectors

Handle cables with care to avoid damage. Apply only the tension required to seat or unseat cables

during insertion or removal from the connector. When possible, handle cables by the connector or pull-

strap. In all cases, avoid bending or twisting the cables, and be sure that the cables are routed in such

a way that they cannot be caught or snagged by parts being removed or replaced.

When servicing the workstation, be sure that cables are placed in their proper location during the

reassembly process. Improper cable placement can damage the workstation.

ENWW

Service considerations

Содержание Z400 - Workstation































































































































































































































































Результаты поиска

Содержание Z400 - Workstation

Отзывы:

Похожие инструкции для Z400 - Workstation

Бренды по названию

Популярные бренды

HP Z400 - Workstation, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание Z400 - Workstation

Отзывы:

Похожие инструкции для Z400 - Workstation

Бренды по названию

Популярные бренды