manualshive.com logo in svg

Honeywell Thor VM3, Руководство пользователя, Страница: 89 / 378

Поделиться
Скачать
Honeywell Thor VM3 Скачать руководство пользователя страница 89

Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide

77

Vehicle 10-60VDC Direct Power Connection

1. The Thor VM3 must not be mounted in the dock. The power switch on the dock must 

be turned 

Off

. The power cable must be UNPLUGGED from the dock.

2. While observing the 

Fuse Requirements

, connect the power cable as close as 

possible to the actual battery terminals of the vehicle (if using unswitched power). 

3. Use proper electrical and mechanical fastening means for terminating the cable. 

Properly sized “crimp” type electrical terminals are an accepted method of 
termination. Please select electrical connectors sized for use with 20AWG 
(0.81mm2) conductors.

4. Refer to the wiring diagrams following this section for wire colors and connections:

•

Ignition Control Wiring Diagram

•

Auto-On Control Wiring Diagram

•

Manual Control Wiring Diagram

5. Route the power cable the shortest way possible removing any left-over cable. The 

cable is rated for a maximum temperature of 105°C (221°F). Therefore, when 
routing this cable it should be protected from physical damage and from surfaces 
that might exceed this temperature. Cable should be protected from physical 
damage from moving parts. Do not expose the cable to chemicals or oil that may 
cause the wiring insulation to deteriorate. Always route the cable so that it does not 
interfere with safe operation and maintenance of the vehicle. 

6. Provide mechanical support for the cable by securing it to the vehicle structure at 

approximately one foot intervals, taking care not to over tighten and pinch 
conductors or penetrate outer cable jacket.

7. Connect the watertight connector end of the power cable to the Thor VM3 dock 

power connector by aligning the connector pins to the power connector; push down 
on the watertight connector and twist it to fasten securely.

8. Secure the power cable to the Thor VM3 using the 

Strain Relief Cable Clamps

.

9.

Place Thor VM3 in the Dock

10. If using the 

Screen Blanking

 feature, install the screen blanking box or switch.

11. Press the 

Power Switch

 on the back of the Thor VM3 dock.

12. Press the 

Power Button

 on the front of the Thor VM3 to turn on the Thor VM3.

Содержание Thor VM3



























































































































































































































































































































































































Отзывы:

Нет отзывов