Honeywell Thor VM3 Скачать руководство пользователя страница 92 | Manualshive

Страница: 92 / 378

Honeywell Thor VM3 Скачать руководство пользователя страница 92

80

Thor VM3 with Microsoft Windows Embedded Compact 7 User Guide

Auto-On Control Wiring Diagram

.

•

Twist the red and red/white wires together and connect to battery positive.

•

Black and black/white wires must be connected to battery negative. Twist these wires
together and connect to battery negative.

•

Green wire must be connected to the vehicle chassis ground.

•

Twist the red and red/white wires together and connect to battery positive.

•

Twist the black wire and a black/white together and connect to battery negative.

•

Green wire is connected to the vehicle chassis ground, which can also be battery
negative.

Fuse Requirements

•

For

12VDC

input, use the 10A fuse from the kit or a slow blow fuse that has a DC

voltage rating greater than 12VDC.

•

For

24VDC

input, use the 6A fuse from the kit or a slow blow fuse that has a DC

voltage rating greater than 24VDC.

Quick Mount

Smart Dock

Circular
Power
Connector

COM1 or COM2
Connector

Existing Circuitry On Vehicle

Battery

Main Switch

-Vo

+Vo

Cable for optional

screen blanking

connection

See

Caution

statement below

Fuse - See

Warning

statement below

(not connected)

Red

Black

Green

Blue

Red/White (if present)

Black/White (if present)

Caution: For battery powered vehicles:

Caution: For internal combustion engine powered vehicles:

Warning: For proper and safe installation, the input power cable must be

connected to a fused circuit on the vehicle. If the supply
connection is made directly to the battery, the fuse should be
installed in the positive lead within 5 inches of the battery’s
positive (+) terminal. Use VM3055FUSE (or equivalent) to
install the fuse as shown below:

«
...
90
91
92
93
94
...
»

Содержание Thor VM3



























































































































































































































































































































































































Отзывы:

Нет отзывов