Hitachi H8/3060 Скачать руководство пользователя страница 667 | Manualshive

Страница: 667 / 995

background image

619

•

In user program mode, FWE can be switched between high and low level regardless of

RES

input.

FWE input can also be switched during execution of a program in flash memory.

•

Do not apply FWE if program runaway has occurred.

During FWE application, the program execution state must be monitored using the
watchdog timer or some other means.

•

Disconnect FWE only when the SWE, ESU, PSU, EV, PV, E, and P bits in FLMCR1 are
cleared.

Make sure that the SWE, ESU, PSU, EV, PV, E, and P bits are not set by mistake when
applying or disconnecting FWE.

4. Do not apply a constant high level to the FWE pin.

T prevent erroneous programming or erasing due to program runaway, etc., apply a high level
to the FWE pin only when programming or erasing flash memory (including execution of flash
memory emulation using RAM). A system configuration in which a high level is constantly
applied to the FWE pin should be avoided. Also, while a high level is applied to the FWE pin,
the watchdog timer should be activated to prevent overprogramming or overerasing due to
program runaway, etc.

5. Use the recommended algorithm when programming and erasing flash memory.

The recommended algorithm enables programming and erasing to be carried out without
subjecting the device to voltage stress or sacrificing program data reliability. When setting the
PSU or ESU bit in FLMCR1, the watchdog timer should be set beforehand as a precaution
against program runaway, etc.

Also note that access to the flash memory space by means of a MOV instruction, etc., is not

permitted while the P bit or E bit is set.

6. Do not set or clear the SWE bit during execution of a program in flash memory.

Clear the SWE bit before executing a program or reading data in flash memory. When the
SWE bit is set, data in flash memory can be rewritten, but flash memory should only be
accessed for verify operations (verification during programming/erasing).

Similarly, when using the RAM emulation function while a high level is being input to the
FWE pin, the SWE bit must be cleared before executing a program or reading data in flash
memory. However, the RAM area overlapping flash memory space can be read and written to
regardless of whether the SWE bit is set or cleared.

A wait time is necessary after the SWE bit is cleared. For details see table 22.40 in section

22.5.6, Flash Memory Characteristics.

7. Do not use interrupts while flash memory is being programmed or erased.

All interrupt requests, including NMI, should be disabled during FWE application to give
priority to program/erase operations (including emulation in RAM).

Bus release must also be disabled.

«
...
665
666
667
668
669
...
»

Содержание H8/3060




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для H8/3060

Бренд: Palm Страницы: 4

Бренд: YASKAWA Страницы: 34

eXtremeRAID 1100

Бренд: Mylex Страницы: 74

Бренд: Dolphin Страницы: 9

F-Tile SDI II Intel Agilex

Бренд: Intel Страницы: 39

ENHANCED PSD 239 H2R

Бренд: ADTRAN Страницы: 2

7798 I/SITE LAN

Бренд: CSI Страницы: 56

Бренд: ADC Страницы: 29

Бренд: ZALMAN Страницы: 8

Бренд: ICP DAS USA Страницы: 60

Бренд: ICS Advent Страницы: 26

Бренд: PairGain Страницы: 68

Бренд: MSI Страницы: 5

234664-002 - ProLiant - ML330T02

Бренд: Compaq Страницы: 160

Бренд: Motorola Страницы: 41

CPEi 750 Series

Бренд: Motorola Страницы: 50

Бренд: Motorola Страницы: 86

Dimetra KVL 4000 Air

Бренд: Motorola Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды