Harris eCDi Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 190

background image

1/3/05

888-2517-001

vii

WARNING: Disconnect primary power prior to servicing.

!

WARNING:

THE CURRENTS AND VOLTAGES IN THIS EQUIPMENT ARE DANGEROUS. PERSON-
NEL MUST AT ALL TIMES OBSERVE SAFETY WARNINGS, INSTRUCTIONS AND REG-
ULATIONS.

This manual is intended as a general guide for trained and qualified personnel who are aware of the
dangers inherent in handling potentially hazardous electrical/electronic circuits. It is not intended to
contain a complete statement of all safety precautions which should be observed by personnel in
using this or other electronic equipment.

The installation, operation, maintenance and service of this equipment involves risks both to
personnel and equipment, and must be performed only by qualified personnel exercising due care.
HARRIS CORPORATION shall not be responsible for injury or damage resulting from improper
procedures or from the use of improperly trained or inexperienced personnel performing such tasks.
During installation and operation of this equipment, local building codes and fire protection
standards must be observed.

The following National Fire Protection Association (NFPA) standards are recommended as reference:

- Automatic Fire Detectors, No. 72E
- Installation, Maintenance, and Use of Portable Fire Extinguishers, No. 10
- Halogenated Fire Extinguishing Agent Systems, No. 12A

!

WARNING:

ALWAYS DISCONNECT POWER BEFORE OPENING COVERS, DOORS, ENCLO-
SURES, GATES, PANELS OR SHIELDS. ALWAYS USE GROUNDING STICKS AND
SHORT OUT HIGH VOLTAGE POINTS BEFORE SERVICING. NEVER MAKE INTERNAL
ADJUSTMENTS, PERFORM MAINTENANCE OR SERVICE WHEN ALONE OR WHEN
FATIGUED.

Do not remove, short-circuit or tamper with interlock switches on access covers, doors, enclosures,
gates, panels or shields. Keep away from live circuits, know your equipment and don’t take chances.

!

WARNING:

IN CASE OF EMERGENCY ENSURE THAT POWER HAS BEEN DISCONNECTED.

!

WARNING:

IF OIL FILLED OR ELECTROLYTIC CAPACITORS ARE UTILIZED IN YOUR EQUIP-
MENT, AND IF A LEAK OR BULGE IS APPARENT ON THE CAPACITOR CASE WHEN
THE UNIT IS OPENED FOR SERVICE OR MAINTENANCE, ALLOW THE UNIT TO COOL
DOWN BEFORE ATTEMPTING TO REMOVE THE DEFECTIVE CAPACITOR. DO NOT
ATTEMPT TO SERVICE A DEFECTIVE CAPACITOR WHILE IT IS HOT DUE TO THE
POSSIBILITY OF A CASE RUPTURE AND SUBSEQUENT INJURY.

«
...
5
6
7
8
9
...
»

Содержание eCDi































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для eCDi

Pacemark PM4410

Бренд: Oki Страницы: 2

interface modul IM33-FSD-Ex/L

Бренд: turck Страницы: 4

Бренд: Cabletron Systems Страницы: 41

Бренд: V2 Страницы: 76

Бренд: SupremeVision Страницы: 5

echomap 40 series

Бренд: Garmin Страницы: 22

Бренд: Icom Страницы: 48

Бренд: Motorola solutions Страницы: 100

Liquisys M CUM 223

Бренд: Endress+Hauser Страницы: 86

Бренд: M-system Страницы: 4

THERMSGARD RGTM2 Series

Бренд: S+S Regeltechnik Страницы: 16

Бренд: Emerson Страницы: 26

Бренд: Emerson Страницы: 48

Бренд: Emerson Страницы: 52

Бренд: Emerson Страницы: 84

Бренд: Craig Страницы: 9

Бренд: Emerson Страницы: 16

Бренд: Kyosho Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды