Harris eCDi Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 190

background image

1-2

888-2517-001

1/3/05

WARNING: Disconnect primary power prior to servicing.

eCDi ™

Section 1 Introduction

1.2

eCDi™ and the PowerCD™ Transmitter

For the Harris PowerCD Digital UHF Transmitter, the eCDi™   has been modified to
include a local GUI touchscreen interface in addition to its normal networking
capabilities. In the PowerCD transmitter the eCDi™   is the local transmitter control
interface using the attached 12" VGA touchscreen and has been renamed the "Display
Unit." This means that the eCDi™   provides both local and remote control for the
PowerCD transmitter.

The PowerCD transmitter will have a Display Unit (an eCDi™ ) in the Driver Cabinet
for system control and monitoring and one in each PA cabinet for individual cabinet
control and monitoring.

Information in this manual covers the basic setup and operation of the remote
networking side of the Display Unit (eCDi™ ). Operation of the Local GUI screens,
mounted on the front of the transmitter Display Units, is covered in the PowerCD
Transmitter Operators manual 888-2574-001.

Also note that the PowerCD Display Unit (eCDi™ ) is a 2 rack unit high box (standard
eCDi™ is 1 rack unit) but uses the same software as all other eCDi™ units.

Figure 1-1 PowerCD™ Display Unit (modified eCDi™ )

PowerCD Display Unit (modified eCDi™ )

Local Transmitter touchscreen
display. Detailed operation of
these screens is covered in the
PowerCD Transmitter Operators
Manual 888-2574-001.

PowerCD

Driver

Cabinet

«
...
14
15
16
17
18
...
»

Содержание eCDi































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для eCDi

Бренд: ABB Страницы: 20

Бренд: ABB Страницы: 24

266 HART Series

Бренд: ABB Страницы: 76

Бренд: ABB Страницы: 20

Бренд: S&C Страницы: 62

FT-227R Memorizer

Бренд: Yaesu Страницы: 42

Бренд: Alinko Страницы: 48

Бренд: Omega Страницы: 32

Бренд: Kanomax Страницы: 27

Бренд: M-system Страницы: 5

Бренд: Icom Страницы: 64

Бренд: PR electronics Страницы: 23

DS-PM1-I16O2-WA

Бренд: HIKVISION Страницы: 2

Бренд: zisa Страницы: 11

Бренд: CDVI Страницы: 2

Бренд: Intek Страницы: 36

Бренд: Intek Страницы: 36

Бренд: Kongsberg Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды