Harris eCDi Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 190

background image

2-22

888-2517-001

1/3/05

WARNING: Disconnect primary power prior to servicing.

eCDi ™

Section 2 Installation & Setup

2.5

APEX Exciter Setup

IMPORTANT:

The APEX exciter software must be 4.0 or later to activate the Ethernet port for
use with eCDi™ . This software (along with the Harris ISP program and program-
ming instructions) can be obtained via download from the Harris Premier web
site or by contacting Harris Technical support. To check the software revision of
your APEX press the “

System Control

” button on the APEX front panel. This

will bring up the screen shown in Figure 2-14. If the software revision is not 4.0
or later, it must be upgraded using the Harris ISP (In-System Programming) soft-
ware, and the files downloaded from the web site, before it will communicate
with the eCDi™ .

Figure 2-14 APEX Software Revision Check

NOTE:

For more information regarding APEX upgrades, see the APEX technical
manual, 888-2491-001.

INFO:

?

The Harris ISP (In-System Programming)2.0 software, provided at no cost, is
used to update the firmware memory in the APEX exciter via the serial port on
the front or back of the unit. The Harris ISP 2.0 program, upgrade software and
instructions can be downloaded from the Harris Premier Website. Please note
that Harris ISP 2.0 must be used. Harris ISP 1.10, which comes loaded on the
Diamond and Sigma transmitter GUI, is not compatible with APEX. Do not load
Harris ISP 2.0 on a Diamond and/or Sigma transmitter GUI as it is not backward
compatible.

Control Software

revision

«
...
42
43
44
45
46
...
»

Содержание eCDi































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для eCDi

Бренд: MAMAC SYSTEMS Страницы: 2

Бренд: S+S Regeltechnik Страницы: 16

Бренд: M-system Страницы: 2

Бренд: dewert okin Страницы: 3

Бренд: Coilcraft Страницы: 16

Бренд: YOKOGAWA Страницы: 85

Бренд: Black Widow Security Страницы: 2

Бренд: Phoenix Contact Страницы: 24

Бренд: Contest Страницы: 8

FMT 380 BT CHARGE

Бренд: Hyundai Страницы: 24

Centronic / B-Tronic EasyControl EC715

Бренд: Becker Страницы: 144

CITIZENS BAND TRANSCEIVER 3-5980

Бренд: GE Страницы: 8

Бренд: GE Страницы: 32

MDS NETio-TB Series

Бренд: GE Страницы: 90

Бренд: GE Страницы: 188

MDS entraNET 2400

Бренд: GE Страницы: 220

MDS Mercury Series

Бренд: GE Страницы: 196

Бренд: GE Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды