Harris eCDi Скачать руководство пользователя страница 17

Страница: 17 / 190

1/3/05

888-2517-001

1-3

WARNING: Disconnect primary power prior to servicing.

Section 1 Introduction

eCDi ™

1.3

Hardware

•

1U device mounted in or near the transmitter control cabinet.

NOTE:

Due to the limitation of the length of the serial cables (50ft) that connect to the
transmitter, the eCDi™ hardware must be mounted within the reach of the maxi-
mum 50 ft. serial cables.

•

Single Board Computer. Includes a 20GB hard drive, 4 port internal ethernet switch

and power supply.

•

1 ethernet port mounted on the front of the unit for configuration and utility monitor-

ing. Eliminates the need to access the rear of the unit after installation.

•

1 ethernet port mounted on the rear for connection to the station LAN or WAN.

•

3 ethernet ports mounted on the rear for permanent interconnect to transmitters and

exciters that have an ethernet interface (RJ-45).

•

2 serial ports mounted on the rear for connection to transmitters and exciters with a

serial interface.

Figure 1-2 eCDi™ Hardware Front Panel

Figure 1-3 eCDi Connections

Uplink jumper. This jumper should be
installed from the LAN connection to the

This port connects to the Station LAN or
WAN or possibly a LAN modem if network
connection does not exist at the site.

Содержание eCDi































































































































































































Результаты поиска

Содержание eCDi

Отзывы:

Похожие инструкции для eCDi

Бренды по названию

Популярные бренды

Harris eCDi, Техническое руководство

Результаты поиска

Содержание eCDi

Отзывы:

Похожие инструкции для eCDi

Бренды по названию

Популярные бренды