manualshive.com logo in svg

General DataComm UAS 7000, Операция

Поделиться
Скачать
General DataComm UAS 7000 Скачать руководство пользователя страница 87

GDC 087R706-000-02

 UAS 7626 DIU

5-7                                                                                                                                               

it disappears the save is complete and the new settings are in effect. 

8.

When you’re done with Unit Configuration, you may either return to the Configuration
Menu screen by pressing the Enter key – identified as 

CR

 (Carriage Return) in the screen

prompt – or return to the Main Menu by typing 

0

 and pressing the Enter key. 

If you start to leave the Unit Configuration screen while there are unsaved changes, the screen 
displays 

*WARNING - EXITING WITHOUT SAVING CHANGES  Continue? [ ] Y(es), N(o)

You can type 

N

 and press the Enter key to keep the Unit Configuration screen on display while 

you perform a save, or you can type 

Y

 and press the Enter key to finish exiting. Unsaved changes 

are lost if you exit without performing a save. 

Alarm Configuration 

Selection 2, Alarm Configuration, from the UAS 7626 Configuration menu calls up the UAS 
7626 Alarm Configuration Submenu shown in Figure 5-5. From that submenu you can select the 
loop for which you intend to perform alarm configuration. 

Each Alarm Configuration Submenu enables you to designate which alarms are to be reported by 
means of SNMP traps when they occur on the loop, and which are to be masked (not reported). 
It also contains the selections for setting thresholds for Bit Error Rate (BER) alarms on the loop. 
Figure 5-6 illustrates the screen for Loop 1; the six Alarm Configuration screens are identical. 

Masking applies only to the SNMP alarm reporting function. The terminal interface Monitor/
Alarms function always displays the actual status of alarm conditions. 

The alarm configuration procedure appears following the figures. 
  

Figure 5-5

Alarm Configuration Menu Screen

                    UAS 7626 Alarm Configuration

  [1] Loop 1 Alarm Configuration

  [2] Loop 2 Alarm Configuration

  [3] Loop 3 Alarm Configuration

  [4] Loop 4 Alarm Configuration

  [5] Loop 5 Alarm Configuration

  [6] Loop 6 Alarm Configuration

  [0] Return to Main Menu      [CR]Return to previous Menu

  Select: [ ]

Содержание UAS 7000











































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды