General DataComm UAS 7000 Скачать руководство пользователя страница 102

Страница: 102 / 106

5-22

UAS 7626 DIU

GDC 087R706-000-02

Figure 3-22

Firmware Download Screen

The Firmware Download screen contains four lines of read-only information display, and four
command selections. The following information is displayed:

Active Firmware Revision – displays the version and revision number of firmware that is
currently operating in the DIU

Standby Firmware Revision – displays the version and revision number of inactive
firmware that the DIU has stored in zipped (compressed) format

Standby Firmware Status – displays one of seven status indications:

Invalid- Blank – new DIU with no standby firmware loaded

Valid- OK – standby firmware loaded and ready for use

Invalid- Checksum Failed – standby firmware corrupted during download

Invalid- Download Aborted – download aborted in progress by SCM

Invalid- Unzip Failed – problem occurred during unzip of standby firmware

Downloading – transfer currently taking place

Calculating Checksum – approximately 40 seconds following completion of transfer

Download Mode – displays the DIU’s selected response to a download of new firmware;
see the command selections below for the potential modes

UAS7626 Firmware Download

Download Status:

Active Firmware Revision : -e.-e.-e

Standby Firmware Revision: vD.-t.

Standby Firmware Status : VALID - OK

Download Mode : DISABLE ALL DOWNLOADS

Select Download Options:

[1] Switch to Standby Firmware

[2] Disable All Downloads

[3] Enable Downloads and Store ZIP

[4] Enable Downloads, UNZIP and Execute

[0] Return to Main Menu [CR] Return to previous Menu

Select: [ ]

Содержание UAS 7000











































































































Результаты поиска

Содержание UAS 7000

Отзывы:

Бренды по названию

Популярные бренды

General DataComm UAS 7000, Операция

Результаты поиска

Содержание UAS 7000

Отзывы:

Бренды по названию

Популярные бренды