manualshive.com logo in svg

General DataComm UAS 7000, Операция

Поделиться
Скачать
General DataComm UAS 7000 Скачать руководство пользователя страница 59

 UAS 7616 DIU

4-5                                                                                                                                               

GDC 087R706-000-02

5.

Fill in the DS0 column with the timeslot assignments to be made in Circuit Configuration: 

A 64 kbps channel can be assigned to any available DS0; the only constraint is to 
make sure there are no duplications. 

When a Channel A is to operate at 128 kbps (Channel B disabled), you must config-
ure both Channel A and Channel B DS0s for the loop because both carry the Channel 
A data. The Channel B DS0 must immediately follow the Channel A DS0; the Chan-
nel B DS0 must not be 1. 

A disabled channel does not require a DS0 assignment when the other channel in its 
loop is 64 kbps or disabled. 

6.

When the worksheet is complete, recheck to make sure no DS0 assignments are duplicated. 

7.

Use the completed worksheet as a guide when you perform Unit Configuration and Circuit
Configuration. 

Unit Configuration

The UAS 7616 Unit Configuration screen shown in Figure 4-4 presents a screen of configuration 
options for setting the operating speeds of the two channels that make up each of the three loops 
the unit can support. Each loop consists of two channels, designated A and B. You can configure 
a loop to support one 64 kbps channel (A or B), two separate 64 kbps channels (A and B), or one 
128 kbps channel (A only). 

Each on-screen option is the setting for one channel, identified by a selection number. Each 
displays its current setting. 

Table 4-1, which follows the figure, lists the settings available for each option. The table is 
followed by the procedure for setting options and saving the configuration settings. 

The four display fields at the top of the screen are fixed values. 
                      

Figure 4-4

Unit Configuration Screen

                     UAS 7616 Configuration

  Unit:

  Network:                          Drop Side

  Module Clk Src:                   System

  Interface:

  Termination Type:                 Line

  Tx Clk Src:                       System

  [1]   Loop1 Channel A Data Rate:     Disabled

  [2]   Loop1 Channel B Data Rate:     Disabled

  [3]   Loop2 Channel A Data Rate:     Disabled

  [4]   Loop2 Channel B Data Rate:     Disabled

  [5]   Loop3 Channel A Data Rate:     Disabled

  [6]   Loop3 Channel B Data Rate:     Disabled

[0] Return to Main Menu   [S] Save   [CR] Return to previous Menu

        Select: [ ]

Содержание UAS 7000











































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды