gefran ADL500 Скачать руководство пользователя страница 39

Страница: 39 / 96

ADL500 • Quick installation guide - Specifications and connection

7.4 ETH-PC Ethernet Interface (RJ45 connector)

The ADL Drive is standard equipped with an RJ45 port for connection via ModbusTCP protocol, used for Drive-PC

communication (with GF_DriveLabs configuration software), and HTTPS protocol used for Drive-PC / network commu

nication (with GF_Drivelabs web application).

Minimum requirements for Ethernet cable: shielded category 5E, maximum length 10 m.

Speed: 100 Mbit/s.

Pin

Signal

Description

IN/OUT

ADL510 ADL530 ADL550

EN0TX+

Data transmission (+)

OUT

Yes

EN0TX-

Data transmission (-)

OUT

Yes

EN0RX+

Data reception (+)

Yes

N.C.

n.c.

Yes

N.C.

n.c.

Yes

EN0RX-

Data reception (-)

Yes

N.C.

n.c.

Yes

N.C.

n.c.

Yes

7.4.1 Ethernet Configuration

Some familiarity and knowledge of IP networking topics is required to establish communication between the

ADL500

and a

Based on the Ethernet configuration, during start-up, the drive acquires an IP address which is retained until reboot.

Any change to the Ethernet configuration is applied when the drive is restarted.

The IP address is acquired based on the following configuration parameters:

Menu

Parameter

Description

NETWORK CONFIG

9604

IP Assignment

IP address assignment method: static or DHCP based

NETWORK CONFIG

9556

IP Address set

Valid only if static assignment is selected. Statically configured IP address

NETWORK CONFIG

9558

IP Netmask set

Valid only if static assignment is selected. Statically configured IP netmask

NETWORK CONFIG

9560

IP Gateway set

Valid only if static assignment is selected. Statically configured IP gateway

The following are read-only parameters:

Menu

Parameter

Description

NETWORK CONFIG

9562

Current IP Address

IP address acquired by ADL500

NETWORK CONFIG

9600

First part of MAC address

MAC Address Low

NETWORK CONFIG

9602

Second part of MAC address

MAC Address High

7.4.2 Point-to-point network topology

The PC is connected directly to the ADL500 drive.

If the ADL500 is configured in “

DHCP

” (IP parameterization, PAR 9604 set to “DHCP”), since no DCHP server is avail

able in this topology, the ADL500 will acquire the local address 169.254.10.10.

Typically, PCs also implement a local connection protocol. Therefore, if the PC is configured to DHCP, it will acquire a

local link address (169.254.x.y), and be able to communicate with the ADL500.
Address acquisition may take up to 2 minutes. If the PC does not implement the local link protocol or does not acquire

a valid address, it can be configured with a static IP address compatible with the local link addresses:
- PC configured for static IP assignment;

- The PC IP address set to 169.254.x.y, with any value except 169.254.10.10, already assigned to ADL500;

- Set the PC IP netmask to 255.255.0.0.

The Windows PC network configuration guide is in the section below.

The ADL550 default IP assignment method is DHCP, so in this topology on first boot, the address 169.254.10.10 will be

acquired and the drive will be reachable from the PC at this address.

Содержание ADL500

































































































Результаты поиска

Содержание ADL500

Отзывы:

gefran ADL500, Быстрый старт, технические характеристики и установка, Страница: 39 / 96

Результаты поиска

Содержание ADL500

Отзывы: