GE CARESCAPE Monitor B850 Скачать руководство пользователя страница 83

Страница: 83 / 192

Configuration

2106778-001

Select

Save

All changes take effect immediately.



Citrix Session Timeout (in Minutes)



Username



Password



Confirm Password

NOTE: The hospital’s IT Administrator or biomedical department can supply these values.
5.

Select

Save

All changes take effect immediately.

7.6.1 Troubleshooting

The information entered must confirm to the following standards:



Citrix Server Address: Any valid IPv4 address.



Initial Program: Name of Citrix-published application to launch.



Citrix User Name: Any valid Windows username. If blank, the user will be forced to enter it
manually.



Citrix Password: Any valid Windows password.



Citrix Timeout: Any integer greater than or equal to 0 and less than 9999.



Citrix Startup Time: Any integer greater than or equal to 0 and less than 9999.

7.6.2 Glossary

Citrix Server Address: IP address or DNS name of Citrix Server.
Initial Program:

Name of Citrix-published application to launch.

Citrix User Name:

ID used to log into Citrix session.

Citrix Password:

Password used to log into Citrix session.

Username

Any valid Windows username. You can leave
this field empty to allow anonymous login.
The maximum length is 128 characters.

Password

Any valid Windows password. You can leave
this field empty to allow anonymous login.
The maximum length is 128 characters.

Confirm Password

The password and confirmed password must
be the same.

Encryption Level

Select one of the following encryption levels:
- "Basic"
- "RC5 (128 bit - Login Only)"
- "RC5 (40 bit)"
- "RC5 (56 bit)"
- "RC5 (128 bit)"

Field name

Description and valid choices

Содержание CARESCAPE Monitor B850

































































































































































































Результаты поиска

Содержание CARESCAPE Monitor B850

Отзывы:

Похожие инструкции для CARESCAPE Monitor B850

Бренды по названию

Популярные бренды

GE CARESCAPE Monitor B850, Руководство по обслуживанию

Результаты поиска

Содержание CARESCAPE Monitor B850

Отзывы:

Похожие инструкции для CARESCAPE Monitor B850

Бренды по названию

Популярные бренды