GE CARESCAPE Monitor B850 Скачать руководство пользователя страница 148

Страница: 148 / 192

CARESCAPE Monitor B850

140

2106778-001

11.5 Problems and solutions

11.5.1

Start-up failures

Speaker failure

1. Speaker cable loose.

1. Connect the speaker cable.

2. Speaker failure.

3. Replace the speaker.

4. Processor board tone

generator or audio amplifier
failure.

5. Replace the processor board.

Problem

Possible causes

Recommended actions

Failure to turn on the patient
monitor.

Power cord is loose.

Ensure that the power cord is connected properly
to the wall outlet and to the patient monitor.

Power cord is faulty.

Check the power cord for wear and damage and
replace if necessary.

The power outlet does not
meet specified
requirements.

Check the power outlet being used:
- Refer to the patient monitor’s supplemental

information manual for power requirements.

- Check the power outlet being used, see section

8.2.2

The cable between the
power supply and the
processor board is loose
or faulty.

Check that the cable is intact and properly
connected to the power supply and the processor
board.

The power supply is faulty. Replace the power supply.

CPU processor board is
faulty.

Replace the CPU processor board.

Message

Possible causes

Possible solutions

Содержание CARESCAPE Monitor B850

































































































































































































Результаты поиска

Содержание CARESCAPE Monitor B850

Отзывы:

Похожие инструкции для CARESCAPE Monitor B850

Бренды по названию

Популярные бренды

GE CARESCAPE Monitor B850, Руководство по обслуживанию

Результаты поиска

Содержание CARESCAPE Monitor B850

Отзывы:

Похожие инструкции для CARESCAPE Monitor B850

Бренды по названию

Популярные бренды