GE 600-1021-95R Скачать руководство пользователя страница 9

Страница: 9 / 113

Concord 4 Series Systems

•

Phone Test Freq. set to 1

•

High Level Rpts set to on

•

Low Level Rpts set to on

•

Comm. Failure set to on

•

RF Tx Timeout set to 4 hours

Central Station Reporting

The panel has been tested with the following central station receivers using SIA and Contact ID

reporting formats:
•

CS-5000 Central Station Receiver

•

Sur-Gard Central Station Receiver with models SG-DRL2A and SG-CPM2

•

Osborne Hoffman Central Station Receiver

Note

The installer must verify the

compatibility between this

panel and the central station

receiver(s) being used.

UL Canada Listed Installations

This section describes the requirements for CUL (UL Canada) Listed installations.

Canadian Standards CSA Certified Accessories

Residential Burglary Alarm System Unit (ULC Subject C1023-1974)

Basic system as described for “UL 1023 Listed Installations” plus:
•

Hardwire Magnetic Contact (13-068 or 13-071) or Wireless Learn Mode Door/Window Sen-

sor (60-362)

•

Siren Timeout set to 5 minutes or more

Residential Fire Warning System Control Unit (ULC-S545-M89)

Basic system as described for “UL 985 Listed Installations” plus:
•

Hardwire Smoke Detector:

System Sensor models

2400 or 2400TH learned into Sensor

Group 26, or

Sentrol (ESL) models

429AT, 521B, or 521BXT learned into sensor group 26

•

Wireless Smoke Sensor 60-506-319.5 or 60-848-02-95 learned into sensor group 26

•

Immediate Trouble Beeps set to on

Note

For 24-hour backup, exter-

nal power drain is limited to

90 mA (during normal

standby condition) using a

4.5 Ah battery, or 190 mA

continuous using a 7.0 Ah

battery.

•

RF TX Timeout set to 4 hours (if system includes SuperBus 2000 RF Transceiver and wire-

less smoke sensors)

•

Siren timeout set to 5 minutes or more.

California State Fire Marshall Listed Installations

Same as Household Fire Warning System (UL 985), plus:
•

SMOKE VERIFY must be set to off

Planning the

Installation

This section describes system capabilities to help you get familiar with the system. “Appendix

A” provides planning sheets with tables that let you record the hardware and programming con-

figuration of the system. Fill in all necessary information ahead of time to help prepare for sys-

tem installation.
The panels have the following capabilities:

Standard Panel

The following describe the basic panel (out-of-box) hardware capabilities.
•

Power:

Input for an AC step-down, plug-in style transformer.

•

Auxiliary Power Output:

Output that supplies 9 to 14 VDC with up to 1 amp for bus

devices and hardwired detectors, such as smoke and motion detectors.

Capabilities

Concord Express V4 Concord 4/Concord

Commercial V4

Zones

Partitions

Bus Devices

User Codes

230

WWW.DIYALARMFORUM.COM

Содержание 600-1021-95R


















































































































Результаты поиска

Содержание 600-1021-95R

Отзывы:

Похожие инструкции для 600-1021-95R

Бренды по названию

Популярные бренды

GE 600-1021-95R, Руководство по установке

Результаты поиска

Содержание 600-1021-95R

Отзывы:

Похожие инструкции для 600-1021-95R

Бренды по названию

Популярные бренды