GE 600-1021-95R Скачать руководство пользователя страница 63

Страница: 63 / 113

Concord 4 Series Systems

The following describes how to program the settings that appear under

SNAPCARDS

Freeze Temp

Acc. Modules-Bus Devices-Unit ID-Energy Options

(Default =

42°F

)

This setting determines the temperature point that the Energy

Saver Module detects a potential freeze (heating failure) con-

dition. The adjustable range is from 40° to 90°F.

Note

This is the same menu found under REPORTING/PARTITIONS

1-6. The setting is used by both the SuperBus 2000 Energy

Saver Module and Dialog RF Thermostat. Individual freeze tem-

perature settings for each device are not allowed.

To change the Freeze Temp setting:

1. With the display showing the desired bus device press #,

then A or B until the display shows

ENERGY OPTIONS

Next, press # then A or B until the display shows

FREEZE

TEMP nn DEGREES

(current setting)

2. Enter the desired freeze temperature (40°–90° F). The dis-

play flashes the entered selection. Press # and the display

shows the new setting.

Temperature

Acc. Modules-Bus Devices-Unit ID-Energy Options

(Default = none)

This setting lets you adjust the Energy Saver Module (ESM)

room temperature setting to match the premises thermostat.

The adjustable range is from 40°–90°F.

Note

To ensure accuracy, wait at least 15 minutes before setting the

ESM temperature to allow the ESM to warm or cool to actual

room temperature.

To change the ESM Temperature setting:

1. With the display showing the desired bus device press #,

then A or B until the display shows

ENERGY OPTIONS

Next, press # and then A or B until the display shows

TEM-

PERATURE nn DEGREES

(current setting)

2. Enter the desired temperature (40°–90° F). The display

flashes the entered selection. Press # and the display shows

the new setting.

Cellular System

Acc. Modules-Bus Devices-Unit ID-Cellular Options

(Default = B)

This setting determines the cellular transmission system (A

or B) used for cellular communication. This information is

provided by the cellular provider based on installation ZIP

code.

To set the Cellular System:

1. With the display showing the desired bus device press 1,

(B) or 2 (A). The display flashes the entered selection.

2. Press # and the display shows the new setting.

WWW.DIYALARMFORUM.COM

Содержание 600-1021-95R


















































































































Результаты поиска

Содержание 600-1021-95R

Отзывы:

Похожие инструкции для 600-1021-95R

Бренды по названию

Популярные бренды

GE 600-1021-95R, Руководство по установке

Результаты поиска

Содержание 600-1021-95R

Отзывы:

Похожие инструкции для 600-1021-95R

Бренды по названию

Популярные бренды