GE 600-1021-95R Скачать руководство пользователя страница 10

Страница: 10 / 113

Concord 4 Series Systems

•

Bus A and B:

Input and output that provides communication between bus devices and the

panel.

•

Siren Driver:

Output that can drive an 8-ohm load and provides intrusion and fire alarm

sounds for partition 1. 6 watts max.

•

2 Onboard Outputs:

Can be used to activate other signalling devices based on system

events.

-Out 1 is a 9 to 14 VDC source output, limited to 1.0 amp max.

-Out 2 is an open-collector output, rated up to 14 VDC, 300mA max.

•

Microphone Input:

Input used for 2-way audio when used in conjunction with the Interro-

gator 200 Audio Verification Module.

•

8 Supervised Hardwire Zones:

Inputs for various hardwired detectors. Zone 8 can be set

up in programming to accept 2-wire smoke detectors. It sources 9 to 14 VDC, 90mA max.

•

Built-In RF Receiver:

Allows use of up to 96 or 32 319.5 MHz. crystal and/or SAW Learn

Mode wireless sensors and touchpads.

•

Phone Line Connection:

Allows panel to communicate with central monitoring station and/

or pagers.

Note

The total current sourced from all terminals cannot exceed 1 amp.

SuperBus 2000 Touchpads

The following touchpads can be used for installer/user programming and system operation.
•

SuperBus 2000 2x16 LCD Touchpad

•

SuperBus 2000 2x20 LCD Touchpad

•

SuperBus 2000 2x20 VFD Touchpad

•

SuperBus 2000 ATP 1000 Touchpad

•

SuperBus 2000 ATP 2100 Touchpad

•

SuperBus 2000 ATP 2600 Touchpad

•

SuperBus 2000 GTS 50

The following touchpads can be used only for installer quick programming, system operation and

user programming.
•

SuperBus 2000 Fixed Display Touchpad

SuperBus 2000 RF Transceiver

The transceiver can be used to receive signals from sensors and touchpad that may be on the

fringe of panel reception. The transceiver is compatible with all 319.5 MHz. crystal and SAW

Learn Mode wireless sensors and touchpads.

SuperBus 2000 RF Receiver

The receiver can be used to receive signals from sensors and touchpad that may be on the fringe

of panel reception. The receiver is compatible with all 319.5 MHz. crystal and SAW Learn Mode

wireless sensors and touchpads.

Note

If installing this module, the Antenna Tamper feature must be turned off.

Power Line Carrier Transformer

Using this transformer allows the use of X10 Powerhouse Lamp Modules for light control and

light activation during alarms.

SuperBus 2000 Voice Only Module

This module provides an output for a speaker that sounds system status and alarm voice mes-

sages.

SuperBus 2000 Phone Interface/Voice Module

This module allows system access and control using touch-tone telephones, on- or off-site. The

module includes an output for a speaker that sounds system status and alarm voice messages.

WWW.DIYALARMFORUM.COM

Содержание 600-1021-95R


















































































































Результаты поиска

Содержание 600-1021-95R

Отзывы:

Похожие инструкции для 600-1021-95R

Бренды по названию

Популярные бренды

GE 600-1021-95R, Руководство по установке

Результаты поиска

Содержание 600-1021-95R

Отзывы:

Похожие инструкции для 600-1021-95R

Бренды по названию

Популярные бренды