GE 600-1021-95R Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 113

background image

Concord 4 Series Systems

13

Connecting 4-Wire Smoke Detectors

Zone input 8 can be used with 4-wire smoke detectors that latch and remain in the alarm state

until power is removed, then restored to the detector. The panel provides this power interruption

from terminal 24 (2W SMK ZONE 8) only when zone 8 is learned into sensor group 26 (fire) and

the Two-Wire Smoke option is on.

Note

Zone 8 must be learned into

sensor group 26 (fire) and

the 2-Wire Smoke feature

must be on for connected

smoke detectors to reset

after canceling a fire alarm.

Table 4 describes the minimum available panel power. Use only 4-wire smoke detectors that

operate at these power limits. Connect up to five Sentrol (ESL) model 449AT (part no. 13-360)

smoke detectors to panel power and zone 8 input as shown in Figure 8.

Connecting Speakers

Note

Install all sirens/speakers

indoors, in a concealed loca-

tion.

The panel provides one siren driver output for intrusion (steady), fire (temporal 3), and auxiliary

(on-off-on-off) alarm sounds. This output trips only for partition 1 alarms.
The output can drive a single 8-ohm speaker or multiple speaker circuit of 8-ohms or higher (as

shown in the following speaker wiring diagrams). Compatible speakers are described below.

Note

Do not connect a bell or

piezo siren to the speaker

output (terminals 7 and 8).

15-Watt Speaker (13-060)

For exterior siren applications, connect the speaker to the panel using 18-gauge wire as shown in

Figure 9.

Figure 9. Connecting Exterior Speakers to the Panel

Table 4: Panel Minimum Available Power

Min. Voltage/Max. Current Available

8.3 VDC, up to 30 mA total (combined alarm) current
8.1 VDC, up to 40 mA total (combined alarm) current
7.6 VDC, up to 60 mA total (combined alarm) current
7.1 VDC, up to 80 mA total (combined alarm) current

Caution

!

To avoid disabling the panel speaker output, do not make speaker connections with the

panel powered up.

Splice

Speaker

Speaker

2 8-Ohm Speakers in
Series (16 Ohms)

7

7

8

8

WWW.DIYALARMFORUM.COM

«
...
16
17
18
19
20
...
»

Содержание 600-1021-95R


















































































































Отзывы:

Нет отзывов

Похожие инструкции для 600-1021-95R

Бренд: ABB Страницы: 20

Бренд: Eaton Страницы: 32

Бренд: Zenith Страницы: 14

Бренд: Observint Страницы: 2

Бренд: Panasonic Страницы: 152

Бренд: Abus Страницы: 162

Бренд: Abus Страницы: 82

Бренд: Abus Страницы: 88

Бренд: Abus Страницы: 2

Бренд: Abus Страницы: 119

Бренд: Rae Страницы: 49

Бренд: UbiBot Страницы: 11

Бренд: D-MAX Страницы: 33

MagnaLatch ALERT

Бренд: D&D Technologies Страницы: 2

MME239 - Micro DVD Home Theater System

Бренд: Magnavox Страницы: 39

Бренд: Olympia Страницы: 62

Бренд: EverFocus Страницы: 12

Бренд: RED SHIELD Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды