GE 600-1021-95R Скачать руководство пользователя страница 60

Страница: 60 / 113

Concord 4 Series Systems

Access Timeout

(09004)

Audio Verification-Partition 1 (Default = 90 sec.)

If the Audio Mode is set to “Instant,” then this set-

ting determines how much time (30–300s, in 2-sec-

ond increments) the central station operator has to

enter the AVM access code after the panel is

accessed for an audio session.

To change the Access Timeout:

1. With the display showing

AUDIO VERIFY OFF/ON

, press A or B until

the display shows

ACCESS TIMEOUT nn SECS

(current setting)

2. Enter the desired time. The display flashes the entered setting. Press #

and the display shows the new setting.

Beep Delay

(09005)

Audio Verification-Partition 1 (Default = 02 sec.)

This setting determines how long AVM access

beeps are delayed (0–300s, in 2-second intervals) at

the beginning of a 2-way audio session.

To change the Beep Delay:

1. With the display showing

AUDIO VERIFY OFF/ON

, press A or B until

the display shows

BEEP DELAY nn SECS

(current setting)

2. Enter the desired time. The display flashes the entered setting. Press

# and the display shows the new setting.

Access Code

(09006)

Audio Verification-Partition 1 (Default = **** or none)

This setting determines the code required to access

the audio verification module to start an audio ses-

sion. If no code is programmed, pressing * starts an

audio session.

To change the Access Code:

1. With the display showing

AUDIO VERIFY OFF/ON

, press A or B until

the display shows

ACCESS CODE nnnn

(current code)

2. Enter the desired

4-digit access code

. The display flashes the

entered code. Press # and the display shows the new setting.

To delete an Access Code:

1. With the display showing

AUDIO VERIFY OFF/ON

, press A or B until

the display shows

ACCESS CODE nnnn

(current code)

2. Press D to delete.

Vox Mic Gain

(09007)

Audio Verification-Partition 1 (Default = 14)

This setting determines the microphone sensitivity

for triggering voice-activated switching (VOX).

For the Interrogator 200, the default setting (14) is

recommended.
Room size, acoustics and furnishings where the

Interrogator 200 is located will influence the set-

ting. Setting range is from 01 (low) to 64 (high).

To change the Vox Mic Gain:

1. With the display showing

AUDIO VERIFY OFF/ON

, press A or B until

the display shows

VOX MIC GAIN nn

(current setting)

2. Enter the desired

2-digit setting

(01 - 64). The display flashes the

entered setting. Press # and the display shows the new setting.

Vox Gain Range

(09008)

Audio Verification-Partition 1 (Default = 64)

This setting determines the gain range for voice-

activated switching (VOX).
Setting range is from 01 (low) to 64 (high). For best

results, this setting should be higher than the Vox

Mic Gain.

To change the Vox Gain Range:

1. With the display showing

AUDIO VERIFY OFF/ON

, press A or B until

the display shows

VOX GAIN RANGE nn

(current setting)

2. Enter the desired

2-digit setting

(01 - 64). The display flashes the

entered setting. Press # and the display shows the new setting.

Manual Mic Gain

(09009)

Audio Verification-Partition 1 (Default = 64)

Not used.

WWW.DIYALARMFORUM.COM

Содержание 600-1021-95R


















































































































Результаты поиска

Содержание 600-1021-95R

Отзывы:

Похожие инструкции для 600-1021-95R

Бренды по названию

Популярные бренды

GE 600-1021-95R, Руководство по установке

Результаты поиска

Содержание 600-1021-95R

Отзывы:

Похожие инструкции для 600-1021-95R

Бренды по названию

Популярные бренды