GE 600-1021-95R Скачать руководство пользователя страница 74

Страница: 74 / 113

Concord 4 Series Systems

Energy Saver Menu

The

ENERGY SAVER

menu lets you set the Energy Saver Module or Dialog RF Thermostat low-

and high-setpoints. These setpoints override the premises thermostat allowing the Energy Saver

Module or Dialog RF Thermostat to activate the furnace/air conditioner.

Attach Lights to Sensors Menu

The

ATTACH LIGHTS TO SENSORS

menu lets you assign a light number to a sensor. Each time the

sensor is activated, the attached light will turn on for 5 minutes. When the 5 minute timer expires

the light will turn off. If the same light is scheduled, it will only turn on during the schedule time.

Low Setpoint

(070)

Energy Saver (Default =

50°F

)

This setting determines the temperature at

which the energy saver module relay closes

to activate the furnace.

Note

The low setpoint cannot be set equal to or

higher than the high setpoint.

To set the Low Setpoint:

1. With the display showing

ENERGY

SAVER

, press #, then A or B until the dis-

play shows

LOW SETPOINT NN DEGREES

(current setting)

2. Enter the desired temperature (45–89°). The display flashes the entered setting.

Press

# and the display shows the new setting.

High Setpoint

(071)

Energy Saver (Default =

90°F

)

This setting determines the temperature at

which the energy saver module relay closes

to activate the air-conditioner.

Note

The high setpoint cannot be set equal to or

lower than the low setpoint.

To set the High Setpoint:

1. With the display showing

ENERGY SAVER

, press #, then A or B until the dis-

play shows

HIGH SETPOINT nn DEGREES

(current setting)

2. Enter the desired temperature (46–90°). The display flashes the entered setting.

Press

# and the display shows the new setting.

Light X to Sensor Y

(08n where

n=light number [1-9] minus 1)

Attach Lights to Sensors (Default =

)

This menu attaches light x to sensor y. Each

time a selected sensor is tripped, the selected

light will turn on and a 5 minute timer will

start.

Note

The sensor must be learned into the current par-

tition before it can be attached.

To attach a light to a sensor:

1. With the display showing

LIGHT 1 TO SENSOR y

(current setting), press A or

B to select the desired light number.

2. Enter the desired sensor number (01–96). The display flashes the entered

setting. Press # and the display shows the new setting.

3. Repeat steps 1 through 2 until all desired lights are attached to sensors.

To detach a light from a sensor:

1. With the display showing

LIGHT 1 TO SENSOR y

(current setting), press A or

B to select the desired light number.

2. Enter 0 as the sensor number and press #.

WWW.DIYALARMFORUM.COM

Содержание 600-1021-95R


















































































































Результаты поиска

Содержание 600-1021-95R

Отзывы:

Похожие инструкции для 600-1021-95R

Бренды по названию

Популярные бренды

GE 600-1021-95R, Руководство по установке

Результаты поиска

Содержание 600-1021-95R

Отзывы:

Похожие инструкции для 600-1021-95R

Бренды по названию

Популярные бренды