GE 600-1021-95R Скачать руководство пользователя страница 28

Страница: 28 / 113

Concord 4 Series Systems

Figure 27. Connecting Panel Power Transformer and Backup Battery

Powering Up the Panel

After connecting and wiring all devices to the panel, you are ready to apply AC and backup bat-

tery power to the panel.

To power up the panel (see Figure 27):

1. Connect the red and black battery leads (included with panel) to the lugs on the panel.

2. Connect the other ends of the battery leads to the battery terminals.

3. Plug the transformer into an outlet that is not controlled by a switch.

Alphanumeric touchpads display

************

, then

SCANNING BUS DEVICES

, and finally a

date and time display.

Note

If alphanumeric touchpads

don’t display anything,

immediately unplug the

transformer and disconnect

the backup battery. Refer to

the “Troubleshooting” sec-

tion.

4. To permanently mount the transformer, unplug it and remove the existing screw securing the

AC outlet cover.

Hold the outlet cover in place and plug the transformer into the lower receptacle.

5. Use the screw supplied with the transformer to secure the transformer to the outlet cover.

Programming

the Panel

For on-site system programming, an alphanumeric touchpad is required.

Entering Program Mode

Entering program mode is done using an installer/dealer code (default = 4321). The system can

be put into program mode only when all partitions are disarmed.

Note

If the system is powered up

after the programming

touchpad is connected or if a

bus command scan is exe-

cuted, the programming

touchpad will be “learned”

into the system and must

later be manually deleted.

To enter program mode:

1. Make sure the system is disarmed in all partitions.

2. Press 8

4321

0. The display shows

SYSTEM PROGRAMMING

To enter programming mode using a programming touchpad:

1. Connect the red, black, green, and white wires from the Programming Touchpad Cable

(60-791) to the power and bus wires/terminals on an alphanumeric touchpad, matching the

+12V (red), Bus A (green), Bus B (white), and GND (black) on each.

2. Make sure the system is powered up and disarmed.

3. Connect the plug on the cable onto the panel programming touchpad header (see Figure 28).

4. Press 8

4321

2. The touchpad sounds one short beep. Press * and verify that the dis-

play shows

SERVICE TOUCHPAD ACTIVE

5. Press 8

4321

0 and the display shows

SYSTEM PROGRAMMING

Panel

Backup Battery Connections

Battery

Red

Black

1 6 . 5 V A C

Terminals

Use extreme caution when securing the transformer to a metal outlet cover. You could

receive a serious shock if a metal outlet cover drops down onto the prongs of the plug

while you are securing the transformer and cover to the outlet box.

Warning

WWW.DIYALARMFORUM.COM

Содержание 600-1021-95R


















































































































Результаты поиска

Содержание 600-1021-95R

Отзывы:

Похожие инструкции для 600-1021-95R

Бренды по названию

Популярные бренды

GE 600-1021-95R, Руководство по установке

Результаты поиска

Содержание 600-1021-95R

Отзывы:

Похожие инструкции для 600-1021-95R

Бренды по названию

Популярные бренды