FSK RHINO 816 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 51

FSK RHINO 816 Скачать руководство пользователя страница 8

FSK-RAP816-V2015.04

8

PCB Layout

1. AC Input
The two wires from the transformer are connected to these
terminals and supply power the system.

2. Network Connections
The network terminals provide connections to the remote keypads
and zone expanders. The RED and BLK terminals provide power
whilst the GRN and YEL terminals are the data signals.

3. Zone Inputs 1 to 8
Detection  devices  such  as  movement  sensors,  vibration  and  door
contacts  are  connected  to  the  zone  input  terminals.  There  are
several ways in which to wire a detection device (see page 10). Each
zone  is  fully  programmable,  see  page  19  for  information  on
programming zones.

4. Aux Tamper Input
This terminal provides tamper detection for auxiliary devices. If it is
not required link it to 0V.

5. Auxiliary 12V
These terminals provide auxiliary power for the external sounder
and detection devices that require 12V power, e.g., moment
sensors. The auxiliary output is protected by an auto resetting fuse
(PTC) rated at 1.1 Amp).

6. Panel Outputs 1 to 4
These are fully programmable high current (1 Amp), switched
negative supervised outputs. Panel outputs 1 and 2 default to bell
and strobe operation, but can be programmed for other functions if
required, see page 31 for programming details. Each output can also
be programmed for supervision monitoring, see page 25.

Panel output 4 defaults as speaker driver and is used for drivi

ng 16Ω

extension loudspeakers (see page 12). If a loudspeaker driver is not
required it can be used as a standard output.

7. RhinoBus Port
The Rhino bus terminals provide connection to Rhino
communication modules.

8. COM Port 1 & 2
COM 1 is provided for local downloading and for third party devices.
COM2 is in parallel with the RhinoBus Port (7) and provides a
different method of connecting compatible modules.

9. Power/Status LED
On steady when either AC or standby battery is present. Flashes
when the communicator is sending data.

10. Lid Tamper Connector
This connector can be used to connect a lid tamper switch to
provide protection for when the enclosure cover is opened.

11. Antenna Screw Connector
This connector provides a screw in connection for the on-board
wireless transceiver antenna.

12. Battery Connections
A  12V  rechargeable  battery  must  be  connected  to  these  two
terminals  in  order  to  provide  continuous  system  operation  in  the
event  of  mains  failure.  The  battery  output  is  protected  by  an  auto
resetting fuse (PTC) rated at 1.6 Amp.

«
...
6
7
8
9
10
...
»

Содержание RHINO 816




















































Отзывы:

Нет отзывов