FSK RHINO 816, Руководство по установке, Страница: 31 / 51

FSK-RAP816-V2015.04 31
6. Panel Outputs and Devices
This section covers programming of the control panel outputs,
communication ports and other devices that maybe connected to
the control panel.
Panel Output Type
This set of options allows the output type (function) to be assigned
to the control panel high current outputs.
Locations:
6111
to
6114
Panel Outputs 1 to 4: Output Type.
Entry Mode: Enter 4 digit location followed by
Enter
, then key
in 4 digit output type(See page 31 for a complete list of output
functions) or press
i
to scroll through list. When finished press
Enter
to accept or
Clear
to cancel.
Panel Output Attributes
This set of options allows the output attributes to be assigned to the
control panel high current outputs.
Locations:
6121
to
6124
Panel Outputs 1 to 4: Output Attributes.
Entry Mode: Enter 4 digit location followed by
Enter
, then use
keys
1
to
8
to toggle options from the list below on or off. When
finished press
Enter
to accept or
Clear
to cancel.
1 Latching
On: The selected output latches on when triggered and is only
cleared when the user resets the system.
Off: The selected output responds normally.
2 Inverted
On: The selected output is inverted, off when active and on when
inactive.
Off: The selected output responds normally.
3 User Test
On: The selected output is activated when the user output test is
selected.
Off: The selected output remains unchanged during the user
output test.
4 Pulse 1
On: The selected output activates for the duration of the “Pulse 1
Time ” system timer, see page 24.
Off: The selected output responds normally.
5 Pulse 2
On: The selected output activates for the duration of the “Pulse 2
Time” system timer, see
page 24.
Off: The selected output responds normally.
6 Delay 1
On: The selected output activates a fter the delay set by the “Delay
1 Time” system timer, see page 25.
Off: The selected output responds normally.
7 Delay 2
On: The selected output activates after the delay set by the “Delay
2 Time” system timer, see
page 25.
Off: The selected output responds normally.
8 Armed Only
On: The selected output only activates if the system is armed.
Off: The selected output responds normally.
If “Pulse 1” and “Pulse 2” options are enable d then the
selected out put activates for the duration of the “Pulse 3
Time ” system timer, see page 24.
If “Delay 1” and “Delay 2” options are enable d then the
selected output activates after the delay set by the “Delay
3 Time ” system timer, see page 25.
Output Types
The output types are grouped together in the following groups:
Group Description
00 Global
Global system output function.
01 Reserved
Not available on the Rhino 816.
02 Control Timer
Control Timers 1 to 5.
03 Remote Control
Remote control outputs 1 to 5.
04 Link Control
Input linked logical conditioned outputs.
10 Zone Count
Zones 1 to 16 count outputs.
20 Zone Mimic
Zones 1 to 16 mimic outputs.
30 Zone Alarm
Zones 1 to 16 alarm outputs.
40 Zone Tamper
Zones 1 to 16 tamper alarm outputs.
50 Zone Masked
Zones 1 to 16 masked outputs.
60 Zone Fault
Zones 1 to 18 fault outputs.
70 Zone Bypassed
Zones 1 to 18 bypassed outputs.
80 User Access
Users 00 to 10 access outputs.
00: Global
The table below list the output function available in this group:
No Type & Description
0000 Not Used
This output type does not activate.
0001 AC Fault
This output type activates when the mains supply has been
removed for the duration of the AC Fail timer.
0002 Reserved
This output type is reserved for future use.
0003 Unset
This output type activates when the system is in the disarmed
state.
0004 Armed
This output type activates when the system is armed in any of
the armed modes (Away or Stay)
0005 Part Armed
This output type activates when the system is armed in any of
the Stay armed modes.
0006 Armed/Alarm
This output type activates when the system is armed and
pulses when an alarm is generated.