Flintec FT-111 AN Скачать руководство пользователя страница 67

Страница: 67 / 146

FT-111(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019

Page

146

[

97- FIRMWARE

]

FIRMWARE INFORMATION

Press key or

key again to enter this menu.

Or press

key to go to the next sub-block.

[

971 INSTRUMENT

]

XX.XX

[

972 OPTION

]

XX.XX

[

973 UPGRADE

] M

Firmware upgrade

Call Flintec service or dealer to upgrade.

[

974 DLC BOARD

]

XX.XX (only FT-111 D)

[

99- DEFAULT

]

DEFAULTS LOADING

Press key or

key again to enter this menu.

Press

key to go to beginning of the sub-block or press

key

to go to the next main block.

[

993 PARAMET DEF

] M

Load parameter's default

(Calibration do not change )

[

994 FACTORY DEF

] M

Load factory defaults

[

995 DEFAULT ADDR

] M

Load default address to digital load cell. (only FT-111 D)

The default address feature solves the problem and provides

access to the load cell functions even if its address and its serial
number are not known.

WARNING: The DLC must be disconnected from the network and
connect as single.

Содержание FT-111 AN



















































































































































Результаты поиска

Содержание FT-111 AN

Отзывы:

Flintec FT-111 AN, Техническое руководство, Страница: 67 / 146

Результаты поиска

Содержание FT-111 AN

Отзывы: