Flintec FT-111 AN Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 146

background image

FT-111(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019

Page

38

of

146

Date and Time

RELATED PARAMETERS: Parameters 251, 252 and 253.

Date format of the country

1. Enter the programming and go to parameter 251,

page 56

2. Press

or

keys to select date format: DMY ( DD.MM.YYYY ), MDY ( MM.DD.YYYYY) or

YMD ( YYYY.MM.DD ) and press

key to confirm.

3. Press

key until [ SAVE : YES ] prompt seen.

4. Press

key to save or press

or

keys to

select “NO” to return operation without saving.

Date adjust

1. Enter the programming and go to parameter 252,

page 56

2. Press numerical keys to enter the date and press

key to confirm.

3. Press

key until [ SAVE : YES ] prompt seen.

4. Press

key to save or press

or

keys

to select “NO” to return operation without saving.

Time adjust

1. Enter the programming and go to parameter 253,

page 56

2. Press numerical keys to enter the time and press

key to confirm.

3. Press

key until [ SAVE : YES ] prompt seen.

4. Press

key to save or press

or

keys to

select “NO” to return operation without saving.

Tilt switch

Tilt switch is used to prevent wrong weighing in case of over tilting of platform.
Connect tilt switch to the Input 4 of the instrument and enable tilt switch by setting the parameter 51A.

[ DUE TO TILTING

]

[ ------ ] prompt is displayed in case of over tilting.

User Language

RELATED PARAMETERS: Parameter 236.

You can select the operation and printout language of the instrument. The available languages are English,
German, French, Italian, Spanish and Turkish. The language of programming is English which has the parameter
code in front of parameter name for easy usage.

Language selection

1. Enter the programming and go to parameter 236,

page 56

2. Press

or

keys to select language and press

key to confirm.

3. Press

key until [ SAVE : YES ] prompt seen.

4. Press

key to save or press

or

keys

to select “NO” to return operation without saving.

Bar graph to display the capacity usage

The Bar graph, which is located on the right side of the display, is used for the graphical visualization of the measured value.
It changes according to the Gross weight even the scale is displaying in Net. The usage of the scale capacity and the
available range are seen on the bar graph. In the example below 70% of the capacity is used and 30% is available.

Minimum tare

You may restrict the taring by entering minimum tare value in to the parameter 518. In case of activated
automatic taring, the instrument tares automatically if the loading is heavier than minimum tare.

Minimum weight for accurate weighing

The instrument produces data output or enables any feature, like printing, if the loading is heavier than
minimum weight. This feature increases the accuracy of your system.

«
...
37
38
39
40
41
...
»

Содержание FT-111 AN



















































































































































Отзывы:

Нет отзывов

Похожие инструкции для FT-111 AN

Бренд: Jeep Страницы: 7

Бренд: Lanier Страницы: 3

Бренд: M-S Cash Drawer Страницы: 2

Бренд: M-S Cash Drawer Страницы: 2

Бренд: Bamo Страницы: 4

Бренд: Obelink Страницы: 2

Бренд: Empire Comfort Systems Страницы: 4

Бренд: Whispbar Страницы: 15

Бренд: FormFit Страницы: 2

Бренд: SICK Страницы: 184

Бренд: FixPosition Страницы: 8

Бренд: E+E Elektronik Страницы: 24

MILSCO KIT# C746700

Бренд: K&M Страницы: 2

Бренд: Car-Interface Страницы: 25

2 Bike Carrier 977

Бренд: Thule Страницы: 6

Бренд: Zenith Страницы: 2

ELKAY VRCGRNTL8 Series

Бренд: Greenspec Страницы: 6

Бренд: Unimig Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды