Flintec FT-111 AN Скачать руководство пользователя страница 145

Страница: 145 / 146

FT-111(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019

Page

144

146

E84 SN NOT MATCH
DLC yy

(1)

The address and S/N of the load
cell do not match.

- Check the DLC and S/N.
- Reenergize the indicator.
- Readdress the DLC.

E85 DLC TIMEOUT
DLC yy

(1)

Communication time out

- Check the DLC connection (RS-485 &
Power supply) hardware.
- Check the DLC and S/N.

E86 DLC COM ERR
DLC yy

(1)

Status error of load cell

- Change load cell.

E87 DLC UNDER
DLC yy

(1)

The DLC is under

- Check mechanical installation and
DLC.

E88 DLC OVER
DLC yy

(1)

The DLC is over

- Check mechanical installation and
DLC.

E89 DLC CHKSUM
DLC yy

(1)

Checksum error

- Check termination resistors.
- Check the DLC connection (RS-485 &
Power supply) hardware.

E90 DLC PWR ERR

Power supply of DLCs could not
detected.

- Check the main board.

E91 DLC SYSTEM

Internal

communication

error

between the DLC board and the
indicator.

- Change the DLC board.
- Change the main board.

E92 DLC UNMATCH

Capacity of the load cell is
different.

- Check capacity of the DLC

1) yy = Number/Address of the digital load cell.

Содержание FT-111 AN



















































































































































Результаты поиска

Содержание FT-111 AN

Отзывы:

Похожие инструкции для FT-111 AN

Бренды по названию

Популярные бренды

Flintec FT-111 AN, Техническое руководство

Результаты поиска

Содержание FT-111 AN

Отзывы:

Похожие инструкции для FT-111 AN

Бренды по названию

Популярные бренды