manualshive.com logo in svg

Exar XRT86VL38, Руководство пользователя

"Exar XRT86VL38" - это высококачественный продукт, который идеально подходит для вашей техники. Скачайте бесплатное руководство по эксплуатации на manualshive.com и узнайте, как максимально эффективно использовать этот уникальный прибор. Благодаря нашему руководству, вы сможете разбираться в устройстве в течение минут!

Поделиться
Скачать
background image

xr

PRELIMINARY

XRT86VL38

REV. P1.0.6 

OCTAL T1/E1/J1 FRAMER/LIU COMBO

34

RxCHN0_4/

RxSCLK0

RxCHN1_4/

RxSCLK1

RxCHN2_4/

RxSCLK2

RxCHN3_4/

RxSCLK3

RxCHN4_4/

RxSCLK4

RxCHN5_4/

RxSCLK5

RxCHN6_4/

RxSCLK6

RxCHN7_4/

RxSCLK7

A10

C17

A26

K25

AB22

AD17

AF11

AF3

B10

F16

B21

J22

Y19

W14

AB7

W7

O

Receive Time Slot Octet Identifier Output-Bit 4 / Receive  Recov-
ered Line Clock Output:

The exact function of these pins depends on whether or not the 
XRT86VL38 is configured to use the receive fractional/signaling 
interface. The two different functions are described below:  

If receive fractional/signaling interface is not used - Receive  
Time Slot Octet Identifier Output-Bit 4

If the fractional/signaling interface is disabled, these output signals 
(RxCHNn_4 through RxCHNn_0) reflect the five-bit binary value of 
the number of Time Slot being received and output to the Terminal 
Equipment via the Receive Payload Data Output Interface.  The Ter-
minal Equipment can use RxCHCLK to sample these five output pins 
in order to identify the time slot being processed. This pin indicates 
Bit 4 of the time slot channel being processed.

If receive fractional/signaling interface is used - Receive Recov-
ered Line Clock Output

If the fractional/signaling interface is enabled, these pins output the 
recovered T1/E1 line clock (1.544MHz in T1 mode and 2.048MHz in 
E1 mode) for each channel

N

OTE

:  Receive Fractional/Signaling interface can be enabled by 

programming to bit 4 - RxFr1544/RxFr2048 bit from register 
0xn122 to ‘1’.

RxCHCLK0

RxCHCLK1

RxCHCLK2

RxCHCLK3

RxCHCLK4

RxCHCLK5

RxCHCLK6

RxCHCLK7

A8

A14

A24

F25

AB24

AE21

AE11

AF5

E10

E15

B20

G19

U18

AB19

AA8

Y5

O

Receive Channel Clock Output

The exact function of this pin depends on whether or not the 
XRT86VL38 is configured to use the receive fractional/signaling 
interface to output fractional data.  

If receive fractional/signaling interface is not used:

If receive fractional interface is not used, this pin indicates the 
boundary of each time slot of an inbound DS1/E1 frame.  In T1 
mode, each of these output pins is a 192kHz clock which pulses 
"High" whenever the Receive Payload Data Output Interface block 
accepts the LSB of each of the 24 time slots.  In E1 mode, each of 
these output pins is a 256kHz clock which pulses "High" whenever 
the Receive Payload Data Output Interface block accepts the LSB of 
each of the 32 time slots. The Terminal Equipment can use this clock 
signal to sample the RxCHN0 through RxCHN4 time slot identifier 
pins to determine which time slot is being processed.

If receive fractional/signaling interface is used:

If receive fractional interface is used, RxCHCLK is the fractional 
interface clock which either outputs a clock signal for the time slot 
that has been configured to input fractional data, or outputs an 
enable signal so that fractional data can be clocked out of the device 
using the RxSERCLK pin. 

If the RxSYNCFRD bit (from register 0xn122) is set to ‘0’, the RxCH-
CLK output pin will output a gapped fractional clock that can be used 
by terminal equipment to clock out fractional payload data using the 
falling edge of the clock.  

If the RxSYNCFRD bit (from register 0xn122) is set to ‘1’, the RxCH-
CLK output pin will output an enable signal and fractional payload 
data is clocked out of the chip using the un-gapped RxSERCLK pin.

N

OTE

:  Receive fractional interface can be enabled by programming 

to bit 4 - RxFr1544/RxFr2048 bit from register 0xn122 to ‘1’.

RECEIVE SERIAL DATA OUTPUT

S

IGNAL

 N

AME

420 P

KG

B

ALL

#

484 P

KG

B

ALL

 #

T

YPE

D

ESCRIPTION

Содержание XRT86VL38



























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для XRT86VL38

Gallagher T20 Installation Note preview
T20
Бренд: Gallagher Страницы: 13
IDTECH NEO 3 VP3350 Quick Start Manual preview
NEO 3 VP3350
Бренд: IDTECH Страницы: 4
EZ Read 800 Plus User Manual preview
800 Plus
Бренд: EZ Read Страницы: 49
Ratoc Systems USB CompactFlash Reader/Writer REX-CF03 Product Manual preview
USB CompactFlash Reader/Writer REX-CF03
Бренд: Ratoc Systems Страницы: 57
Diamond Multimedia Radeon X1300PCI Specification Sheet preview
Radeon X1300PCI
Бренд: Diamond Multimedia Страницы: 1
Conceptronic CMULTiCRSi User Manual preview
CMULTiCRSi
Бренд: Conceptronic Страницы: 21
Renkforce CR27E Operating Instructions preview
CR27E
Бренд: Renkforce Страницы: 4
Tenda W322P V2.0 Technical Specifications preview
W322P V2.0
Бренд: Tenda Страницы: 2
JARLTECH MSR 1218 SERIES Operation Manual preview
MSR 1218 SERIES
Бренд: JARLTECH Страницы: 18
Nedap MACE MM QR Quick Reference Manual preview
MACE MM QR
Бренд: Nedap Страницы: 5
IDTECH ViVOpay VP3600 User Manual preview
ViVOpay VP3600
Бренд: IDTECH Страницы: 8
IDTECH MiniSmart II User Manual preview
MiniSmart II
Бренд: IDTECH Страницы: 13
Sunrich Tech CP-140 User Manual preview
CP-140
Бренд: Sunrich Tech Страницы: 13
SUNRICH TECHNOLOGY IP-120 User Manual preview
IP-120
Бренд: SUNRICH TECHNOLOGY Страницы: 16
CNET CWP-905 User Manual preview
CWP-905
Бренд: CNET Страницы: 26
KTI Networks KF223TX Installation Manual preview
KF223TX
Бренд: KTI Networks Страницы: 27
Gemplus GPR400 Reference Manual preview
GPR400
Бренд: Gemplus Страницы: 36
Newer Technology MAXPower Quick Installation Manual preview
MAXPower
Бренд: Newer Technology Страницы: 49

Бренды по названию

Популярные бренды

Загрузить еще бренды