ECR International G95V Скачать руководство пользователя

Страница: 52 / 56

DIAGNOSTIC CODES FOR STATUS LED

FAULT CODE HISTORY

The control stores the last 5 fault codes in memory.

When the pushbutton switch is pressed for less

than 5 seconds, the control will ﬂash the stored

fault codes when the switch is released. The most

recent fault code is ﬂashed ﬁrst, the oldest last.

Fault history may be cleared by holding the push-

button switch for more than 5 seconds.

A RED LED is provided to indicate furnace operating status
LED Condition

Fault Condition

Check

6 Flashes

Not Used

7 Flashes

Pressure switch cycle

lockout

Pressure switches operation, tubing and wiring.

Obstruction or restrictions in venting preventing

proper air ﬂow.

8 Flashes

Lockout due to too many

ﬂame dropouts

Check system for proper ground.

Dirty, oxidized or failed ﬂame sensor.

9 Flashes

Not used

10 Flashes

Flame present with gas off

Flame at main burner.

Gas valve.

A GREEN LED is provided to indicate high heat state

LED off

No demand for high heat

LED on

High heat demand, operating normally

LED ﬂashing

High heat demand, high pressure switch not closed

Содержание G95V

























































Результаты поиска

Содержание G95V

Отзывы:

Похожие инструкции для G95V

Бренды по названию

Популярные бренды

ECR International G95V, Руководство по установке и эксплуатации

Результаты поиска

Содержание G95V

Отзывы:

Похожие инструкции для G95V

Бренды по названию

Популярные бренды